manualshive.com logo in svg

Pentair Raychem NGC-UIT2-0RD, Installation Instructions And Specifications, Page: 8 / 8

Share
Download
Pentair Raychem NGC-UIT2-0RD Installation Instructions And Specifications Download Page 8

© 2010-2015 Pentair.  

NORTH AMERICA 

Tel: +1.800.545.6258

Fax: +1.800.527.5703

Tel: +1.650.216.1526

Fax: +1.650.474.7711

[email protected]

EuROpE, MIddlE EAsT, AfRICA

Tel: +32.16.213.511

Fax: +32.16.213.603

[email protected]

AsIA pACIfIC

Tel: +86.21.2412.1688

Fax: +86.21.5426.2937

[email protected]

lATIN AMERICA

Tel: +1.713.868.4800

Fax: +1.713.868.2333

[email protected]

Pentair and NGC are owned by Pentair or its global affiliates. All other trademarks are the property of their respective owners. Pentair reserves the right 

to change specifications without prior notice.

WWW.PENTAIRTHERMAL.COM

8 / 8

GB-RaychemNGCUIT20RD-IM-H58531     INSTALL-168      05/15

INDUSTRIAL HEAT TRACING SOLUTIONS

Reset

RS-485-1

Termination

Pull-down

Pull-up

Termination

3 2 1

ON

RS-485-2

Termination

rs-485 configuration switches

reset switch

The configuration switches are found on the right side of the  

NGC-UIT2-ORD. Refer to the table below for settings.

The Reset switch can be found on the side of the NGC-UIT2-ORD. A 

pointed object is required to press the reset switch and restart the 

NGC-UIT software.

position

switch

 on

 off

 comments

Pull-down

(As-shipped default) RS-485 network 

“–” signal is forced to a determinate 

state when idle.

RS-485 network “–” signal is not 

forced to a determinate state when 

idle.

One device (typically this NGC-UIT2-ORD) on the 

RS-485 network should force the network “-“ signal 

to a determinate state.

Pull-up

(As-shipped default) RS-485 network 

“+” signal is forced to a determinate 

state when idle.

RS-485 network “+” signal is not 

forced to a determinate state when 

idle.

One device (typically this NGC-UIT2-ORD) on the 

RS-485 network should force the network “+“ signal 

to a determinate state.

Termination

(As-shipped default) RS-485 network 

is terminated with 120-ohm resistor.

RS-485 network is not terminated.

Terminate the device (NGC-UIT2-ORD or other) that 

is at each end of the RS-485 network, for a total of 

two terminated devices. No other devices on the 

network should be terminated.

Summary of Contents for Raychem NGC-UIT2-0RD









Reviews:

No comments