manualshive.com logo in svg

Pentair Raychem JBS-100-ECP-A, Installation Instructions Manual, Page: 11 / 14

Share
Download
Pentair Raychem JBS-100-ECP-A Installation Instructions Manual Download Page 11

IndustrIal Heat tracIng  sOlutIOns

EN-RaychemJBS100ECPA-IM-H57463     05/16

Optional

Alarm

Contacts

Com

NC

NO

To user 

annunciation panel

Line

Line/ Neutr

al

Earth

Power

Terminal

Block

Power In 

Pentair Thermal

Management

recommends 

the use of a 

conduit drain to 

prevent water 

condensation 

build-up

10

11

connecting alarm
•  The controller has a form C contact for remote 

annunciation of low and high alarms. If an external 

alarm is required, then alarm wiring can exit the 

enclosure via the 3/4 inch power conduit hole, as long 

as the insulation rating of the alarm wire is equal to 

the power wire. (Per NEC 303-3 (c)).

Alarm Relay

Form C: 2 A at 277 Vac, 2 A at 48 Vdc

Normally energized; changes state upon an alarm.

•  Install conduit and fittings as 

shown. To minimize loosening 

due to pipe vibration, use 

flexible conduit.

•  Pull in power and ground 

wires, strip off 1/2 in (13 mm) 

of  insulation and terminate.

11 / 14

Earth

Line/ Neutr

al

Line

Power

Terminal

Block

To

Heating

Cable

MI heating cable

Grounding strap

RTD

Input

R R W

Red

White

8

9

connecting Heating cable
•  Insert the two heating 

cable wires into the 

terminal block marked 

“To Heating Cable” and 

the grounding strap 

to “Earth” and tighten 

terminals. Confirm 

connection by pulling 

on the wires.

connecting rtd
•  Insert the three RTD wires into 

the terminal block marked “RTD 

Input”. Match the colors (Reds 

to R, White to W), and tighten 

terminals. Confirm connection by 

pulling on the wires.

Summary of Contents for Raychem JBS-100-ECP-A















Reviews:

No comments