background image

General Safety Information   

2

DeSCrIptIon

These Myers Stainless Steel Submersible Sump Pumps are 

designed for drainage of sump pits and flooded basements, 

dewatering flooded areas, and to provide laundry drainage. 

Operates automatically. Has a 115V, 60 Hz., single phase, 

permanent split capacitor motor. Pump casing, suction strainer, 

impeller and shaft are all stainless steel. Permanently lubricated 

ball bearings never need lubrication. Automatic thermal 

overload protection. Equipped with a 15’ 18/3 grounding-type 

power cord and tethered float switch. 
Non-clog cast stainless steel impeller, ceramic shaft facings, and 

stainless steel oil chamber for seal lubrication.

SpeCIfICatIonS

Power supply required ............................................115V, 60 HZ.
Motor duty ................................................................Continuous*
Dedicated Circuit Requirement (minimum) ................... 15 Amps
Pump Discharge ....................................................... 1-1⁄4" MNPT 

Discharge Adapter: ..........................................1-1⁄4" FNPT Elbow 

1-1⁄4" MNPT-1-1⁄2" FNPT Adapter

Passes solids up to: ................................................................ 3/4"

*note:

 For continuous operation, water depth must be at 

least 2".

UnpaCkInG anD InSpeCtIon

Handle with care. Check items received against packing list 

to be sure that all equipment has been received. Inspect for 

shipping damage. If found, file claim with carrier immediately.

General Safety InformatIon

reaD anD folloW  

Safety InStrUCtIonS!

Electrically powered sump pumps normally give many years of 

trouble-free service when correctly installed, maintained, and 

used. However, unusual circumstances (interruption of power 

to the pump, dirt/debris in the sump, flooding that exceeds the 

pump’s capacity, electrical or mechanical failure in the pump, 

etc.) may prevent your pump from functioning normally. To 

prevent possible water damage due to flooding, consult your 

retailer about a secondary AC sump pump, a DC backup sump 

pump, and/or a high water alarm. See the “Troubleshooting 

Chart” in this manual for information about common sump 

pump problems and remedies.
Know the pump application, limitations, and potential hazards.
Disconnect power before servicing.
Release all pressure within system before servicing any component.
Drain all water from system before servicing.
Secure discharge line before starting pump. An unsecured 

discharge line will whip, possibly causing personal injury and/or 

property damage.
Check hoses for weak or worn condition before each use, 

making certain that all connections are secure.
Periodically inspect sump, pump, and system components. Keep 

free of debris and foreign objects. Perform routine maintenance 

as required. 
Personal Safety:
1.  Wear safety glasses at all times when working with pumps.
2.  Keep work area clean, uncluttered, and properly lighted – 

replace all unused tools and equipment.

3.  Keep visitors at a safe distance from work area.
4.  Make workshop child-proof – with padlocks, master 

switches, and by removing starter keys.

When wiring an electrically driven pump, follow all electrical 

and safety codes that apply.

this equipment is only for use on 115 volt (single phase) 

and is equipped with an approved  3-conductor cord and 

3-prong, grounding-type plug.

 

to reduce risk of electric shock, pull plug 

before servicing.

 This pump has not been investigated for use in 

swimming pool areas. Pump is supplied with a grounding conductor 
and grounding-type attachment plug. Be sure it is connected only to a 
properly grounded grounding-type receptacle. Where a 2-prong wall 
receptacle is encountered, it must be replaced with properly grounded 
3-prong receptacle installed in accordance with codes and ordinances 
that apply.

All wiring should be performed by a qualified electrician.
Make certain power source conforms to requirements of your 

equipment.

performanCe

SpeCIfICatIonS

model

Hp

motor

full load

amps

rpm

minimum

Circuit req.

(amps)

liquid

temperature

range

Switch

Setting

pumps

Down

to

on

off

DS33p1

1/3

2.8

3450

15

32°/120° F

12.0"

6.0"

1-3/8"

DS50p1

1/2

4.1

3450

15

32°/130° F

12.0"

6.0"

1-3/8"

DS75p1

3/4

6.4

3450

15

32°/130° F

12.0"

6.0"

1-3/8"

model

Hp

Gpm of Water @ total feet of Head

Shutoff

5’

10’

15’

20’

DS33p1

1/3

16.0

8.5

  1.0

16.0’

DS50p1

1/2

34.0

25.0

  15.5

7.0

23.5’

DS75p1

3/4

45.5

34.0

  21.5

12.0

26.2

Summary of Contents for Myers DS33P1













Reviews: