manualshive.com logo in svg

Pentair MASTERTEMP 125, Installation And User Manual

Share
Download
Pentair MASTERTEMP 125 Installation And User Manual Download Page 8

MASTERTEMP

 

125 Pool and Spa Heater Installation and User’s Guide

 

                     

P/N 475114 Rev. F  9/2020

      |

WARNINGS AND SAFETY INFORMATION 

(CONTINUED) 

 

WARNING

 —

 

Risk of fire or explosion from incorrect fuel use or faulty fuel conversion. 

Do not try to run a 

heater set up for natural gas on propane gas or vice versa. Only qualified service technicians should 
attempt to convert heater from one fuel to the other. Do not attempt to alter the rated input or type of 
gas by changing the orifice. If it is necessary to convert to a different type of gas, consult your Pentair 
dealer. Serious malfunction of the burner can occur which may result in loss of life. Any additions, 
changes, or conversions required in order for the appliance to satisfactorily meet the application needs 
must be made by a Pentair dealer or other qualified agency using factory specified and approved 
parts. The heater is available for use with G20, G25 or G31 gas only. It is not designed to operate 
with any other fuels. Refer to the nameplate for the type of gas the heater is equipped to use. 

 

•  Use heater only with the fuel for which it is designed.

 

•  If a fuel conversion is necessary, refer this work to a qualified service technician or gas supplier  
  before putting the heater into operation.

 

WARNING —

 

Risk of explosion if unit is installed near propane gas storage.

 Propane (LP) gas is heavier than 

air. Consult local codes and fire protection authorities about specific installation requirements and 
restrictions. Locate the heater away from propane gas storage and filling equipment as specified by 
the Standard for the Storage and Handling of Liquefied Petroleum Gases (latest edition).

 

WARNING

 — 

Risk of fire. 

Do not place articles on, near or against the heater.

 

WARNING —

 

Risk of burn hazard.

 To reduce the risk of injury, do not touch the side heater vent  cover when the 

heater is operating. Side heater vent covers are HOT and can burn when touched causing personal 
injury. Do not allow children to play on or around heater or associated equipment.

 The average 

temperature of the heaters flue exhaust is 204 degrees Celsius (°C).

 

 

WARNING —

 

Risk of asphyxiation if exhaust is not correctly vented. Follow venting instructions exactly 
when installing heater.

 Do not use a draft hood with this heater, as the exhaust is under pressure 

from the burner blower and a draft hood will allow exhaust fumes to blow into the room housing the 
heater. The heater is supplied with an integral venting system for outdoor installation.  

 

CAUTION —

 

Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper 
and dangerous operation. Wiring errors can also destroy the control board.

 

 

•  Connect heater to 

240

 Volt, 50 Hz., Single Phase power only.

 

•  Verify proper operation after servicing.

 

•  Do not allow children to play on or around heater or associated equipment.

 

•  Never allow children to use the pool or spa without adult supervision.

 

•  Read and follow other safety information contained in this manual prior to operating this pool  
 heater.

Vent

Cover

viii

Warning and Safety Instructions

Summary of Contents for MASTERTEMP 125





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands