manualshive.com logo in svg

Pentair MASTERTEMP 125, Installation And User Manual

Share
Download
Pentair MASTERTEMP 125 Installation And User Manual Download Page 20

P/N 475114 Rev. F  8/2020

 

MASTERTEMP 125 Pool and Spa Heater Installation and User’s Guide

|   11

(*) 

For service access, it is advisable to allow for

  sufficient clearance on at least one door panel.

15 cm

(6 in)

15 cm

(6 in)

15 cm

(6 in)

15 cm*

(6 in)

*

Figure 15.

HEATER CLEARANCES — General Requirements

INDOOR INSTALLATION OR OUTDOOR SHELTER 

The following clearances must be maintained from the nearest walls: 

(See Figure 15 and 16)

TOP............................... 15 cm (6 in)
EXHAUST SIDE ........... 15 cm (6 in)
HEADER SIDE ............. 15 cm (6 in)
DOOR PANELS*  ......... 15 cm (6 in)

Note 

(*) For service access it is advisable to allow for sufficient clearance on at least one door panel. The heater 

is designed for installation on combustible flooring. For installation on carpeting, the heater must be mounted on 

a metal or wood panel that extends at least 9 cm (3 in) beyond the base of the heater. 

Note: Wall sensitive to heat 

(for example wood), must be protected by a suitable insulation.

 If the heater is installed in a closet or alcove, the entire 

floor shall be covered by the panel. On an outdoor shelter installation, the exhaust discharges into a vent pipe. Orient 

the heater so that the vent pipe does not interfere with adjustment of the operating controls. The control panel located 

on the top panel can be rotated to any of the three sides of the heater for easy access. However, the control panel must 

not be located on the side where the vent is located.

INDOOR VENTING — General Requirements

If you are considering connecting this heater to a pre-existing vent system, make sure that the vent system meets the 

appropriate venting requirements as given in this manual on pages 11-16. If not, replace the vent system. 

DO NOT

 

use a draft hood with this heater. The MasterTemp heaters are capable of a 270° C (518° F) discharge rotation and 

with a vent gas temperature less than 204° C (400° F). The total length of the horizontal run must not exceed the 

length that is listed in Table 6 on page 13.

Outlet Air

Opening

Inlet Air

Opening

Chimney or Gas Vent

Vent Cap and 

Riser Furnished

by Installer

Side

Wall Vent

Heater

Chimney or Gas Vent

Vent Cap and 

Riser Furnished

by Installer

Side

Wall Vent

Outlet Air Opening

Inlet Air Opening

OUTSIDE VENT COVER REMOVAL

The heater is supplied from the factory with a built-in stackless outside vent for outdoor 
installation. Remove the outside vent cover for outdoor shelter installation.

Figure 16.

Section 1. Installation 

Summary of Contents for MASTERTEMP 125





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands