manualshive.com logo in svg

Pentair MASTERTEMP 125, Installation And User Manual

Share
Download
Pentair MASTERTEMP 125 Installation And User Manual Download Page 30

P/N 475114 Rev. F  8/2020

 

MASTERTEMP 125 Pool and Spa Heater Installation and User’s Guide

|   21

LOW VOLTAGE 
RACEWAY

HigHigh

High Voltage Cover Panel Tabs (3)

 

Front door

Hi

High Voltage Cover Panel slots (3)

Flip down the Outdoor Control Panel to ac

-

Circuit board and low 
voltage compartment

Loosen Outdoor Control Panel 

Retaining screws

Figure 29.

To connect the MasterTemp heater to the load center: 

   

BEFORE REMOVING THE HIGH VOLTAGE COVER PANEL FROM THE   

 

 

 

 

LOAD CENTER OR POWER CENTER ENCLOSURE SWITCH OFF THE 

 

 

 

POWER AT THE HOUSE MAIN CIRCUIT BREAKER BOX.

1.  Switch OFF AC power to the enclosure at the main house panel circuit breaker.
2.  Unlatch the front door latch and open the front door. Remove the two retaining screws from the High Voltage 

Cover Panel and remove the panel. See Figure 33.

3.  Loosen the two retaining screws securing from the top edge of the Outdoor Control Panel. Fold down the 

Outdoor Control Panel to access the circuit board sockets connectors for the electrical connections. 

Connecting the RS-485 Cable from the Heater to the Load Center

Note: Use a 22 AWG four conductor low voltage RS-485 cable to connect to the MasterTemp heater to the   
IntelliCenter Control System Load Center: 

4.  Run the RS-485 cable from the heater’s control board RS-485 COM port terminal connector to the Load 

Center or Power Center. See wiring connection Figure 30 on next page.

5.  Insert the cable into the one of the plastic grommet fittings, located on the lower left side of the enclosure and 

pull the cable up through the low voltage to the circuit board, as shown below.  

6.  Strip back the outer jacket four inches. Strip back each conductor ¼-inch. 

7.  IntelliCenter Control System COM Port (J4 or J5): Insert the conductors into the COM Port screw terminals 

located on the top of the IntelliCenter Control System circuit board (see diagram below). Secure the 
conductors with the screws. For wiring details, refer to the pin configuration shown below. Note: Multiple 
conductors may be inserted into a single screw terminal. 

Section 1. Installation 

Summary of Contents for MASTERTEMP 125





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands