Pentair EASYTOUCH PL4 Installation Manual Download Page 9 | Manualshive

Page: 9 / 48

background image

EASYTOUCH

®

PL4/PSL4 Control Systems Installation Guide

EASYTOUCH

®

PL4/PSL4 Control Systems Installation Guide

1

Section 1

EasyTouch PL4/PSL4 Control Systems Configuration

• EasyTouch

Pool Lite 4 Circuit (PL4 - Four circuit pool only system)

• EasyTouch

Pool and Spa Lite 4 Circuit (PSL4 - Four circuit pool and spa shared equipment

system)

EasyTouch PL4/PSL4 Control Systems provides control for high voltage (120 VAC / 240 VAC)
equipment, automatic valve actuators, pumps, lighting, a conventional heater or a solar heating
system, heat pump, and the optional IntelliChlor

®

Salt Chlorine Generator and IntelliChem

®

Water

Chemistry Controller.
Pool and spa service operations can be manually controlled from the Outdoor Control Panel located
in the Power Center at the pool equipment pad.
Also available are the optional Indoor Control Panel, Wireless Controller, iS4 Spa-Side Remote, and
the QuickTouch

®

Remote Controller for complete control of pool and spa operations from inside you

home or outside around your pool area. The Power Center dimensions are

20” H x 17” W x 5¼” D

.

EasyTouch

®

PL4/PSL4 Control Systems Power Center Overview

Features

• Dimensions: 20” H x 17” W x 5-1/4” D

• Includes three 25 AMP HP relays

• 120/240 V transformer with secondary side circuit protection

• Provides ample space for all high and low voltage wiring

requirements

• Multiple knockouts for different sizes of conduit are supplied

• GFCI side knockout

• The Power Center enclosure is used with external circuit

breakers/sub-panel for pool and spa equipment

Kit Contents

The following items are included in the Power Center kit

• EasyTouch PL4/PSL4

Control Systems Power Center Enclosure

•  Relays: Qty. 4
•  Actuators: (Qty. 2 for PSL4 Control System only)
•  Temperature Sensor (all models): Water Sensor Long Cable (Qty. 1) (o-ring and hose clamp)

Air sensor - Short cable (Qty. 1)

•  Wiring Diagram Label - To affix to the inside front door (see power center door).
•  Parts bag: Relay screws (Qty. 0, 4, 8, or 10) label sheet
•  EasyTouch PL4/PSL4 Control Systems Power Center Installation Guide (this manual).
•  For additional information, refer to the EasyTouch PL4/PSL4 Control Systems User’s Guide

(P/N 522461).

EasyTouch

®

PL4/PSL4

Control System Power Center

Introduction

«
...
7
8
9
10
11
...
»

Summary of Contents for EASYTOUCH PL4

















































Reviews:

No comments

Related manuals for EASYTOUCH PL4

Brand: ABB Pages: 138

Brand: ABB Pages: 116

Relion 615 series

Brand: ABB Pages: 136

Brand: Hamworthy Pages: 10

Brand: GARDTEC Pages: 48

Brand: FAAC Pages: 64

Brand: National Instruments Pages: 10

Brand: Balboa Instruments Pages: 10

Brand: Quantum Data Pages: 36

Brand: BEIER-Electronic Pages: 22

Brand: Danfoss Pages: 37

Brand: Daikin Pages: 44

Brand: FASAR ELETTRONICA Pages: 2

Brand: Faro Barcelona Pages: 8

Brand: Faro Pages: 3

Brand: YASKAWA Pages: 456

Brand: GCE Pages: 24

Brand: Samson Pages: 78

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands