Pentair 33WC Instruction Manual Download Page 5 | Manualshive

Page: 5 / 12

Pentair 33WC Instruction Manual Download Page 5

© 2013 Pentair Equipment Protection

87976540

- 5 -

MOUNTING GASKET

MOUNTING CUTOUT DIMENSIONS

89045090

PRINCIPLES OF OPERATION

If electrical power to the air conditioner is interrupted and reapplied immediately, (within 3 to 5 seconds), the

compressor may not restart due to the high back pressure of the compressor. It takes a minimum of one (1)

minute after shut-down for the compressor suction and discharge pressures to equalize in order for the air

conditioner to restart.
Operating the air conditioner below the minimum ambient temperature or above the maximum ambient

temperatures indicated on the nameplate voids all warranties.
It is recommended that the warranty section of this manual be read in order to familiarize yourself with

parameters of restricted operation.
The moisture that the enclosure air can contain is limited. If moisture flows from the drain tube continuously this

can only mean that ambient air is entering the enclosure. Be aware that frequent opening of the enclosure’s door

admits humid air which the air conditioner must then dehumidify.

«
...
3
4
5
6
7
...
»

Summary of Contents for 33WC













Reviews:

No comments