background image

P/N 472032

                     Rev. A  1-2-02

4

Operation

This instruction manual provides operating
instructions, installation and service information
for the MiniMax NT Standard high performance
heater. The information in this manual applies to
the MiniMax NT Standard 200, 250, 300, and
400 models.
It is very important that the owner/installer read
and understand the section covering installation
instructions, and recognize the local and state codes
before installing the MiniMax NT Standard. History
and experience has shown that most heater damage
is caused by improper installation practices.

    SAFETY RULES

1. Spa or hot tub water temperatures should never

exceed 104° F.  A temperature of 100° F. is
considered safe for a healthy adult.  Special
caution is suggested for young children.

2. Drinking of alcoholic beverages before or during

spa or hot tub use can cause drowsiness which
could lead to unconsciousness and subsequently
result in drowning.

3. Pregnant women beware!  Soaking in water

above 100° F. can cause fetal damage during the
first three months of pregnancy (resulting in the
birth of a brain-damaged or deformed child).
Pregnant women should stick to the 100° F.
maximum rule.

4. Before entering the spa or hot tub, the user

should check the water temperature with an
accurate thermometer.  Spa or hot tub
thermostats may err in regulating water
temperatures by as much as 4° F.

5. Persons with a medical history of heart disease,

circulatory problems, diabetes or blood pressure
problems should obtain their physician's advice
before using spas or hot tubs.

6. Persons taking medication which induce

drowsiness, such as tranquilizers, antihistamines
or anticoagulants should not use spas or hot
tubs.

Should overheating occur or the gas supply fail to shut off, turn off the manual gas control valve to the
appliance.  Do not use this heater if any part has been under water.  Immediately call a qualified service
technician to inspect the heater and to replace any part of control system and gas control which has been
under water.

 

WARNING

WARRANTY INFORMATION

The MiniMax NT Standard pool heater is sold with
a limited factory warranty. 

Specific details are

described on the back cover of this manual and a
copy of the warranty and warranty registration
card are included with the product

.

 Return the

warranty registration card after filling in the serial
number from the rating plate inside the heater.

Pentair Pool Products’ high standards of excellence
include a policy of continuous product improvement
resulting in your state-of-the-art heater. We reserve
the right to make improvements which change the
specifications of the heater without incurring an
obligation to update the current heater equipment.

Operation

Summary of Contents for MiniMax NT Standard 200

































Reviews: