background image

3

  

056255661 (02-01-22)     

SAFETY SYMBOLS

 This is the safety alert symbol. When you see this symbol 

on your pump or in this manual, look for one of the following 
signal words and be alert to the potential for personal injury:

DANGER

 warns about hazards that will cause serious 

personal injury, death or major property damage if ignored.

 warns about hazards that can cause serious 

personal injury, death or major property damage if ignored.

 warns about hazards that will or can cause 

minor personal injury or property damage if ignored.

The word 

NOTICE

 indicates special instructions that are 

important but not related to hazards.

CALIFORNIA PROPOSITION 65 WARNING

 This product and related accessories contain 

chemicals known to the State of California to cause cancer, 
birth defects or other reproductive harm.

GENERAL SAFETY

 

Carefully read and follow all safety instructions in this 
manual and on the unit itself.

 

 Do not touch an operating motor. Modern 

motors can operate at high temperatures. To avoid burns 
when servicing pump, allow it to cool for 20 minutes after 
shutdown before handling.

 

Follow all applicable local and state codes and regulations.

 

Keep safety labels in good condition, replacing any missing 
or damaged labels.

 

DO NOT

 run the pump dry. Dry running can overheat the 

pump, (causing burns to anyone handling it) and will void 
the warranty.

 

Wear safety glasses at all times when working on pumps.

 

Keep work area clean, uncluttered and properly lighted. 
Store all unused tools and equipment.

 

DO NOT

 use to pump flammable liquids. Never operate the 

pump in an explosive environment. Arcing from the motor 
brushes, switch or excessive heat from an improperly 
cycled motor may cause an explosion.

ELECTRICAL SAFETY

DANGER

 

Hazardous voltage. Can shock, burn, or kill.

 

When installing, operating, or servicing this pump, follow the 
safety instructions listed below.

 

DO NOT

 install pump in any location classified as 

hazardous by National Electrical Code, NFPA 70 or the 
Canadian Electrical Code.

 

DO NOT

 modify the cord or plug. When using cord and 

plug, use a grounded outlet only. When wiring to a system 
control, connect ground lead to the system ground.

 

DO NOT

 allow the plug on the end of the electrical cord to 

be submerged.

 

DO NOT

 use extension cords. They are a fire hazard and 

can reduce voltage sufficiently to prevent pumping and/or 
damage motor.

 

DO NOT

 handle or service the pump while it is connected 

to the power supply.

 

Plug the pump into a 3-wire, grounded, grounding-
type receptacle. When wiring this pump follow all local 
electrical and safety codes and ordinances as well as the 
most recent National Electric Code (NEC-ANSI/NFPA 70).

 

All pumps have a GROUND WIRE that is connected to a 
screw in the metal motor housing. This wire goes to the 
receptacle or control box which must be connected to 
a good outside GROUND such as a metal water pipe or 
GROUND STAKE driven at least 8 feet into the ground.

 

WHEN OVERLOAD CURRENT PROTECTION IS PROVIDED BY 
INSTALLER: 

USE WITH APPROVED MOTOR CONTROL THAT MATCHES 

MOTOR INPUT IN FULL LOAD AMPERES WITH OVERLOAD ELEMENT(S) 
SELECTED OR ADJUSTED IN ACCORDANCE WITH CONTROL 
INSTRUCTIONS.

WHEN MOTOR HAS BUILT-IN OVERLOAD PROTECTION: 

USE 

WITH APPROVED MOTOR CONTROL THAT MATCHES MOTOR 
INPUT IN FULL LOAD AMPERES.

SAFETY INSTRUCTIONS

Summary of Contents for SHEF100S

















Reviews: