Pendulum CNT-90 Getting Started Manual Download Page 6

Chapter 3

Operating the Counter

Introduction

While  this  counter  has  a  vast  array  of  features  and operating 

modes, the majority of the most useful functions can be learned 

in just a few minutes. The following descriptions and exercises 

will help you grasp the basics of operation. They will also serve 

as an introduction to  some  of  the  more  advanced  features.  It 

will take you about half an hour to gather experience enough to 

continue exploring the world of counting on your own.

User Interface

The  fundamental  idea  has  been  to  facilitate  even  complex 

measurements  by  a  consistent  interactive  user  interface  that 

fully exploits the large graphic display. The casual as well as the 

frequent user will benefit from a combination of hard and soft 

keys. In this context hard keys either act immediately or open 

fixed menus, whereas the function of soft keys depends on the 

display information.

Getting Familiar with the 

Counter

The front panel is laid out in a logical fashion. Take a few seconds 

to find the sections described below on the front panel of your 

counter. See also the figure on this page. It will help you locate 

the different keys faster.

6

Summary of Contents for CNT-90
















Reviews: