PenBits BACHMANN CLASS 24 Assembly Instructions Manual Download Page 4 | Manualshive

Page: 4 / 52

PenBits BACHMANN CLASS 24 Assembly Instructions Manual Download Page 4

General Notes

A Few Words …
Safety
The Instructions

File Fo rm a t
Structure
P rinting

T a gs
Slo ts
De gre e o f Etching
C usps
Fo lds

Soldering
Spring Winding
Warranties

A Few Words …

These advices, taken, several moons since, from John Lythgoe's instructions for his Formil
Model Engineering Dyna-drive kits, have proved to be useful and enduring tenets:

"Proceed with patience and due care at ALL stages and a free-running locomotive
should result."
"Allow sufficient time to spread the conversion over a number of modelling sessions."
"Work in good light conditions. Use an anglepoise-type lamp if possible. A self-
supported magnifier is a useful aid."

Safety

Our kits are intended to be assembled by adult modellers, with some workshop experience
and  awareness, who  are  able  to exercise  due  care  and  attention  when  handling  the
materials and carrying out the various operations involved. Many of the metal components
have  sharp  edges.  Chemical  products  used  in  assembly  can  be  injurious  through  contact
with skin or eyes, ingestion or inhalation.  Some processes involve high temperatures.  The
user  should  be aware  of  and  follow the  manufacturers'  or  suppliers'  safety  data  and
instructions for all tools, materials and products.

The Instructions

File Format

The instructions are available on line in both HTML and pdf formats. The HTML
versions have one page for each major section, whilst the pdf versions have a

single file for each kit.

Structure

General Notes

4/51

(c) PenBits Model Railways, All Rights Reserved

27/09/2021

«
...
2
3
4
5
6
...
»

Summary of Contents for BACHMANN CLASS 24





















































Reviews:

No comments