manualshive.com logo in svg

Pelsue PH Series, Product Manual

Share
Download
Pelsue PH Series Product Manual Download Page 16

501144-001 - Product Manual - PH Series Personnel Hoists - Revision 03 Revision Date - 2018-06-13

Page 16

Figure 5b

: PH Series Hoist

Drive Handle Installation

SPRING

PLUNGER

5.5 - Field Operation (continued)

4.  Personal Fall Arrest System (PFAS)

In some entry/retrieval applications, OSHA, ANSI and local standards require that the entrant be connected to a Personal 

Fall Arrest System. It is the responsibility of the operator to be aware of these requirements and follow them. Always 

use a full body harness on the entrant when attached to a PFAS to minimize potential injury to the entrant. Application 

limitations for the hoist also apply to a PFAS.

5.  Installation/Removal

Pelsue PH Series Personnel Hoists are most commonly used on or with a Pelsue Davit System. Normally, the hoist is 

removed from the davit for storage and transporting. When installing or removing the hoist from the davit, follow this 

procedure:

 

a.  Installing:

 

 

i)

   Be  sure  the  quick  connect  mounting  bracket  is  securely  fastened  to  the  structure.  Refer  to  appropriate  

Structure Manual for bracket mounting details. See Figure 5a.

 

 

ii)

   Attach the hoist to the quick connect mounting bracket. Raise the hoist so that the slots on the quick release 

bracket of the hoist can slide onto the anchoring rod on the quick connect mounting bracket. See Figure 

5c.

 

 

iii)

  Align the holes on the quick release bracket and the mounting bracket. Secure the hoist using the  

   

 

 

      attached detent pin. See Figure 5d.

Figure 5c

: PH Series Hoist

Mounting

Figure 5a

: Davit System

Mounting Bracket

QUICk CONNECT

MOUNTING BRACkET

#500101-002

ANCHORING

ROD

BRACkET

SLOTS

Figure 5d

: PH Series Hoist

Detent Pin

PIN

HOLES

DETENT

PIN

Figure 5e

: PH Series Hoist

Fully Mounted

Note:

 Prior to mounting the hoist, the drive handle must 

be installed to the hoist chassis by pulling on the ring of the 

spring plunger and inserting the handle. See Figure 5b

Summary of Contents for PH Series





































Reviews:

No comments

Brands by name

Popular brands

Load more brands