www.pelprostoves.com
7081-148H
27
DO NOT OVERFIRE THIS STOVE:
This may cause serious damage to your stove and void your warranty.
It also may create a fire hazard in your home. IF ANY EXTERNAL PART OF THIS UNIT BEGINS TO GLOW, YOU ARE
OVERFIRING. Immediately press the “OFF” button on the control board.
CAUTION:
Never use liquid or volatile fire starters to start a fire in your stove
! Do not in-stall or operate your stove in
any room where any liquid or volatile fuels or any other highly combustible items are in the air or stored in the room. These
could cause a safety hazard.
NOTE:
If the fire does not start, your stove will continue to feed pellets and the fans will run for approximately 15 minutes. The stove
will then automatically shut off. If this happens, some unburned pellets will build up in the burn grate. To restart the fire, clean the
excess pellets out of the burn grate and follow the above "Lighting a Fire".
NOTE:
Some odors may be given off a new stove during the initial few hours of burning while the stove and the paint are being
cured. These odors are not harmful. However, ventilating the room until the odors disappear is strongly recommended. Run your
appliance on HIGH #4 setting and turn off the room heating fan for approximately 1/2 hour, to quickly aid in limiting these odors.
Operating Instructions
-
Lighting Your Appliance
Before lighting a fire check to ensure the Burn Grate is clean and adjusted and the Ash Tray is not full.
For safety reasons use extra caution when lighting a stove that is HOT!
Lighting stove manually (No Igniter)
In the NON-Thermostat Mode
1.
Push firmly on the
FEED RATE or START
touch
pad.
-The
COMBUSTION FAN
(exhaust) will start and
operate at full speed for 60 seconds, then adjust
downward to match feed rate #1
-The
CONVECTION FAN
(heating) will start and the
LED will go solid on LOW setting
- The
AUGER CYCLE
LED
will go solid for 3 sec-
onds, indicating signal being sent to auger motor.
2. Place a small amount of a solid fuel fire starter such
as those made from sawdust and wax or use wood
shavings, in the bottom of the burn grate. Add a
small handful of pellets to the starter material.
Add a
small amount of fire starter over the pellets.
CAUTION: DO NOT USE ANY FLAMMABLE
LIQUIDS SUCH AS GASOLINE, GASOLINE-
TYPE LANTERN FUEL, KEROSENE, CHAR-
COAL LIGHTER FLUID, OR SIMILAR LIQUIDS
TO START OR FRESHEN-UP THE FIRE! KEEP
ALL SUCH LIQUIDS WELL AWAY FROM THE
HEATER WHILE IT IS IN USE.
3. Light the fire starter and slowly close the
MAIN
DOOR
, leaving it about 1 inch open. When the
pellets are burning, close and latch the main door. If
the fire goes out when the main door is closed, add
more fire starter, re-light the fire and leave the main
door open an inch or so until the pellets start to
burn, then close and latch the main door.
4. Adjust
FUEL RATE
and
FAN
SPEED
to desired
settings you require upon completion of startup
sequence.
Lighting stove with Auto-Ignitor
In the NON-Thermostat Mode
1. Push firmly on the
FEED RATE or START
touch pad.
-The
COMBUSTION FAN
(exhaust)
will start and operate at full speed for
60 seconds, then adjust downward to
match feed rate #1
-The
CONVECTION FAN
(heating) will
start and the LED will go solid on LOW
setting
- The
AUGER CYCLE
LED
will go solid
for 3 seconds, indicating signal being
sent to auger motor.
-The
IGNITER
LED will light up solid and
the 300 watt igniter will begin to operate.
2. On a primed
AUGER
system pellets will begin
to fall into the
BURN GRATE
, and the
AUTO
SELF IGNITER
will automatically ignite the
pellets in approx. 3 – 5 min.
Note: If stoves fails to light within 15
minutes, shut off the stove, remove the
pellets from the burn grate and repeat
step 2. If stove fails to ignite a second
time, disconnect and contact your
dealer
.
3. Adjust the
FUEL RATE
and the
FAN
SPEED
to your desired settings you require upon
completion of startup sequence.
