Pelican SDDLMT2B Quick Start Manual Download Page 1

READ ME!

• 

NOTE: CASE MAY BE MOUNTED ON HINGE OR LATCH SIDE ACCORDING TO ACCESS PREFERENCE - FROM OUTSIDE OR INSIDE PICKUP BED.

THANK YOU FOR PURCHASING A PELICAN™ CARGO CASE GEN2 SADDLE MOUNT KIT FOR TOYOTA TACOMA. THIS KIT USES THE FACTORY TOYOTA 

CARGO DECK RAIL. BEFORE YOU START, TAKE A MOMENT TO FAMILIARIZE YOURSELF WITH THE FITTING INSTRUCTIONS AND THE COMPONENTS 

RECEIVED. REFER TO PAGE 1 FOR A LIST OF ALL THE COMPONENTS, QUANTITIES AND TOOLS REQUIRED.

SINCE 197

6

For Pelican™ BX55SBX85S CARGO Cases in Toyota Tacoma truck beds using factory rail mounting.

IMPORTANT WARNING!

LATCHES AND MOUNTING KIT CARE

It is critical that Pelican™ Cargo Mounts and Cases be properly installed and securely attached to your vehicle. Failure to properly secure 

the Mounts and Cargo Case to your vehicle could result in serious injury and even death. You are responsible for the fitment of the Mounts and 

Cargo Cases to your vehicle. You must therefore periodically inspect the equipment for wear and damage. Replace if in doubt. If you have 

limited mechanical experience you should not attempt to install the equipment. You should have the equipment installed by a professional 

installer if you have any doubts about your abilities. 

It is imperative that the user check the fit security of the cases to the vehicle after an initial brief period of driving and adjust if required. 

Pelican recommends the user do so periodically and if road conditions change (i.e. freeway to dirt "road"), again check the fit security of the 

attachment of the Case to the vehicle.

Periodically check the latches and mounting hardware to ensure there are no loose parts. Continual exposure to daylight may cause the black hardware 

finish to dull. To maintain the glossy finish, occasionally apply a light coat of UV protectant. After exposure to salty coastal climates or snowy regions, 

rinse off the mounts with water to remove salt deposits. To help prevent corrosion, apply a non-reactive silicone-based oil or spray to nuts and bolts.

Take care not to damage painted surfaces during mounting and dismounting. Touch-up paint is recommended as needed to prevent corrosion.

SDDLMT2B

PELICAN™ CARGO CASE

SADDLE CASE MOUNT, GEN 2 FOR TOYOTA

 TACOMA

 TRUCK

PELICAN PRODUCTS, INC. 

23215 Early Avenue, Torrance, CA 90505  

Pelican.com • 310.326.4700

Pelican Products, Inc. (“Pelican”) guarantees its Pelican™ Cargo cases for a lifetime against 

breakage or defects in workmanship. This lifetime warranty does not cover mounting hardware, 

which Pelican warrants against defects in materials and workmanship for three years from the date 

of purchase. To the extent permitted by law, Pelican’s liability is limited to the case and not its 

contents and in no event shall Pelican’s liability to the purchaser for damages exceed the purchase 

price of the case in respect of which damages are claimed.
TO THE EXTENT PERMITTED BY LAW: (A) THIS WARRANTY IS IN LIEU OF ALL WARRANTIES, EXPRESS 

OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY 

AND FITNESS FOR A PARTICULAR PURPOSE; (B) ALL OTHER IMPLIED WARRANTIES AND ANY LIABILITY 

NOT BASED UPON CONTRACT ARE HEREBY DISCLAIMED AND EXCLUDED; AND (C) IN NO EVENT SHALL 

PELICAN BE LIABLE FOR ANY INDIRECT, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR 

SPECIAL DAMAGES, REGARDLESS OF WHETHER A CLAIM FOR SUCH DAMAGES IS BASED ON WARRANTY, 

CONTRACT, NEGLIGENCE OR OTHERWISE .
With valid dated proof of purchase, Pelican will either repair or replace any broken or defective 

product, at our sole option. Certain products are available for a limited time only.  If a claim is made 

involving one of these products, Pelican reserves the right to replace a broken or defective product 

with a standard Pelican product of comparable size and quality if no comparable limited edition 

product is available at the time of a claim. TO THE EXTENT PERMITTED BY LAW, THIS SHALL BE THE 

SOLE AND EXCLUSIVE REMEDY OF THE PURCHASER.
To make a warranty claim, the purchaser must complete the warranty claim form at  

https://www.pelican.com/us/en/support/warranty/. Any warranty claims shall be made by the 

purchaser as soon as practicable and, with respect to the mounts and related hardware, no later 

than three years from the date of purchase. The purchaser must provide valid dated proof of purchase 

and obtain a return authorization number from Pelican Customer Service prior to returning any 

product, and is responsible for paying for all warranty freight costs. If Pelican determines that any 

returned product is not defective, within the terms of this warranty, the purchaser shall pay Pelican 

all costs of handling, return freight and repairs at Pelican’s prevailing rates.

This warranty does not cover normal wear and tear including but not limited to scratches, dents 

or tears, aesthetic surface damage which may be caused by oxidation or by the natural breakdown 

of colors caused by exposure to the elements. All warranty claims of any nature are barred if the 

product has been altered, damaged or in any way physically changed, or subjected to abuse, misuse, 

negligence or accident.
Some states and countries do not allow limitations on how long an implied warranty lasts or the 

exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion 

may not apply to you. This warranty gives you specific legal rights, and you may have other rights 

which vary from state to state and country to country.
In Australia: The benefits provided to you under this warranty are in addition to your rights and 

remedies as a consumer under the Australian Consumer Law as contained in the Competition and 

Consumer Act 2010 (Cth) (“the Act”). Nothing in this warranty limits the rights or obligations of a 

party under the Act in relation to the supply to consumers of goods which cannot be limited, modified 

or excluded. If applicable, our goods come with guarantees that cannot be excluded under the Act. 

Consumers are entitled to a replacement or refund for a major failure and compensation for any other 

reasonably foreseeable loss or damage. Consumers are also entitled to have the goods repaired or 

replaced if the goods fail to be of acceptable quality and the failure does not amount to a major 

failure. If you are not a consumer under the Act, then your rights may be limited. To make a warranty 

claim, the purchaser may contact Pelican Products Australia, Suite 2.33, West Wing, Platinum Bldg., 

Erina NSW 2250, Tel: +612 4367 7022, or email: [email protected]. Any claims should be 

made as soon as practicable. To expedite claims, the purchaser should obtain a return authorization 

number from Pelican Customer Service prior to returning any product.  The purchaser is responsible 

for paying for all freight costs. If Pelican determines that any returned product is not defective, 

within the terms of this warranty or the Act, the purchaser may pay Pelican all costs of handling, 

return freight and repairs at Pelican’s prevailing rates. In the event that Pelican determines that 

any returned product is defective, within the terms of this warranty or the Act, Pelican shall pay the 

purchaser all reasonable costs of the purchaser in making a claim under this warranty.

PELICAN™ CARGO CASES AND MOUNTS   

LIMITED LIFETIME WARRANT Y (CASES) AND THREE YEAR WARRANT Y (MOUNTS) 

©2021 Pelican Products, Inc. Part No. SDDLMT-002B-BLK   Rev. A   DE21   5-36225 

Toyota and Tacoma are registered trademarks of Toyota Motor Corporation. All other trademarks are  

registered and/or unregistered trademarks of Pelican Products, Inc., its subsidiaries and/or affiliates.

 For warranty details go to www.pelican.com/warranty

Summary of Contents for SDDLMT2B







Reviews: