Storage
Always empty the Steam Cleaner after use. Never
leave water in the tank when storing the unit.
1. Turn off the power by unplugging the Steam
Cleaner.
2. Empty all remaining tank pressure by pressing
the steam trigger (2).
3. Allow the unit to cool completely (10 minutes
minimum).
4. When the appliance is cold, lock the steam
trigger into close lock position and remove the
accessories.
5. Empty all remaining water from the tank by
tilting the unit to one end. Never leave water in
the tank when the unit is not in uses stored.
6. Replace the filler cap and store the steam clea-
ner in a safe and dry place.
Warning:
Do not expose steam cleaner to frost.
Do you have hard water?
If the tap water used is very calcareous, it is recom-
mended to use distilled or demineralized water in
the steam cleaner.
If the use of very calcareous water is unavoidable,
it is recommended to clean the water tank
regularly.
How to clean the water tank?
To clean the water tank and descale, proceed as
follows.
Do not use detergent to clean the tank.
1. Mix a 50/50 solution of 250 ml of white vinegar
and 250 ml of water. You can use the mea-
suring cup.
2. Pour the solution into the unheated cold tank
using the funnel.
3. Leave the solution in the tank for about 30
minutes.
4. After 30 minutes, empty the tank.
5. Repeat steps 1 to 4, if necessary.
6. Rinse will with water.
7. Replace the tank filler cap and store in a safe
and dry place.
Warning:
Never clean the water tank while it is
still hot. Always turn off and unplug steam cleaner
before cleaning.
Disposal and recycling
Do not dispose of electrical appliances through
household garbage.
The electrical appliance is in a packaging to pre-
vent any damage during transport. This packaging
is a raw material and can therefore be reused later
or re-introduced into the raw material circuit. The
electric appliance and its accessories are made of
serval material, for example metals and plastics.
Eliminate defective components through the speci-
Use of steam cleaner
1. Make sure the Steam Cleaner is unplugged and
the switch in the OFF position (12).
2. Unscrew the tank filler cap (5) by turning coun-
terclockwise.
3. Using the measuring cup (10) and the funnel
(11), fill the Steam Cleaner with 1.BL of water.
(This will produce about 35 minutes of steam.)
4. Replace the filler cap by screwing it clockwise.
5. Attach the extension tubes to the steam handle
(1) to obtain a steam mop or attach the acces-
sory adapter (23).
6. Connect the appliance and press the switch
(12) to the ON position.
7. Two lights come on. The indicator light (12)
comes on to indicate that the power is turned
on. The orange steam light (13) comes on to
indicate a rise in steam pressure in the applian-
ce.
8. The appliance is ready for use when the orange
steam indicator light (13) goes out, the max
pressure will be approximately 5 bar , depen-
ding on the water level in the tank,
9. During use, the orange steam indicator light
(13) may turn on again. This indicates that the
steam pressure may not be large enough. In
this case, release the steam trigger (2) a few
moments. When the orange steam indicator
light (13) goes off again, you can resume using
steam.
10. If the pressure drops under low pressure (yel-
low zone of gauge), the steam flow may not be
sufficient depending on the accessory used. In
this case, release the steam trigger (2) and wait
until the pressure gauge (6) reaches the red
zone again.
11. When activating the steam trigger (2), water
may appear. This is quite normal because at
the beginning, the steam takes a little time to
arrive and the water condenses in the hose and
the extension tubes. After a few moments the
water will turn into steam and there will be no
more water.
12. When activating the steam trigger (2), a lot of
water can flow. This may be due to a residue of
steam from the previous use that has turned
into water. Empty this water by operating the
steam trigger over a bucket or sink. Once this
water has passed, you can use your device.
13. When using the accessories, the surface you
are cleaning may be wet. This is due to the
steam that turns into water in contact with this
surface. Provide a sponge or cloth to wipe this
surface.
14. After use, press the switch (12) in the OFF posi-
tion and disconnect.
Be careful, never direct steam on yourself or anyo-
ne else as it may cause burns.
