Contact
PELA Tools
Solängsvägen 13
SE-513 70 Borås
Phone: 033-202650
E-mail: [email protected]
Environmental protection /
Scrapping
Recycle any unwanted material,
do not throw it in the household
rubbish. All machines, accessories
and packaging must be sorted and left
at a recycling center and disposed
of in an environmentally friendly
manner.
Save this manual
You will need the manual for the safety warnings
and precautions, assembly instructions, operating
and maintenance procedures, parts list and
diagram. Keep your invoice with this manual. Write
the invoice number on the inside of the front cover.
Keep the manual and invoice in a safe and dry
place for future reference.
Read all instructions before using this tool
1. Keep the work area clean. Cluttered areas invite
injuries.
2. Consider work area connections. Don’t use
tools in damp, wet, or poorly lit locations. Don’t
expose to rain. Keep the work area well lit.
3. Keep children away. All children should be kept
away from work area.
4. Stock idle equipment. When not in use, tools
should be locked up in a dry location to inhibit
rust. If possible, store in an area out of reach of
children.
5. Use the right tool. Don’t force a small tool or
attachment to do the work of a larger
industrial tool. Don’t use a larger industrial tool.
Don’t use a tool for a purpose for which it was
not intended.
6. Dress properly. Don’t wear loose clothing or
jewelry. Non-skid footwear is recommended
when working to prevent slipping. Wear
protective hair covering to contain long hair.
7. Use eye protection. Wear approved impact
goggles at all times when using this tool.
8. Secure work. Use clamps or a vise to hold
the work if possible. It’s safer than using your
bands and it frees both hands to operate the
tool.
9. Don’t overreach. Keep handles dry. Clean, and
free from oil and grease. Follow
instructions for lubricating and changing
accessories.
10. Maintain tool with care. Keep handles dry,
clean, and free from oil and grease. Follow
instructions for lubricating and changing
accessories.
11. Check damaged parts. Before using any tool,
any parts that appear damaged should be
carefully checked to determine that it will
operate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting, and other conditions that may affect
its operation. Any part that is damaged should
be properly repaired or replaced by an
authorized service centre unless otherwise
indicated elsewhere in the instruction manual.
12. Replacement parts and accessories. When
serving, use only identical replacement parts.
Only use accessories intended for use with this
tool.
13. Don’t operate tool if under the influence of
alcohol or drugs. Read warning labels on
prescription to determine if your judgment or
reflexes are impaired while taking drugs. If
there is any doubt, don’t operate the machine.
14. Never stand on a tool. If the tool is tipped over,
serious injury or product damage could result.
Unpacking
The 50-inch slip roll machine should come
assembled when unpacked. Look for loose parts in
the packing material before discarding. If any are
found, try and find the part on the parts list or on
the exploded view of the machine, and reinstall the
part.
Assembly and adjustment
1. Mount the Slip Roll machine to a bench by
bolting the base of the machine (#21) to the
bench.
2. Adjust the distance between Shaft 1 (#8) and
Shaft 2 (#20) if necessary.
A. The distance between Shaft 2 (#20) and
Shaft 1 (#8) can be adjusted by turning the
Adjusting Bolts (#35)
B. To decrease the distance between the two
shafts, turn the Adjusting Bolt (#35) clockwise.
C.To increase the distance, turn the adjusting
bolt (#35) counter clockwise.
3. Adjust the distance between shaft 1 and shaft
3 if necessary
A. The distance between shaft 3 (#7) and shaft
1 (#8) can be adjusted by turning the adjusting
bolts (#22).
B. To decrease the distance between the two
shafts, turn the adjusting bolts (#22) clockwise.
C. To increase the distance, between the two
shafts, turn the adjusting bolts (#22)
4. Removal of shaft 1 (#8) if necessary. The left
end of shaft 1 is mounted on a square bushing
(#5), and the right end of shaft 1 is mounted
through the right stand (#9)
