PEKO ETS-1700E Installation And Operating Manual Download Page 3

        

Installa on

 

and

 

Opera ng

 

Manual

 

 

Page

 

3

 

 

The contents of this user manual describes the functions of 
the ETS-1700E drying cabinet and how it should be used. It 
also includes instructions for installation and maintenance. 

PEKO Equipment Limited reserve the right to make 
improvements and/ or changes to the cabinet and to the 
contents of this manual. Origination: 03/11/17 

DATA PLATE DETAILS 

Located inside the cabinet on the left hand side panel.                         

 

For Your Reference  

Date

 

of

 

purchase:

  

___________________

 

Serial

 

Number:

  

___________________

 

ADVICE ON SAFE OPERATION 

This advice on safe operation has been compiled so that you can avoid incorrect use and unnecessary 
risks of accidents, and should be read before the drying cabinet is installed and used. 

CAUTION

:  This equipment is only intended to be used to dry textiles washed in water. 



Do not allow children to play in, on or with the 
drying cabinet. Close supervision of children is 
required when they are in the immediate vicinity 
of the cabinet. 



If the power cable is damaged it must be 
replaced immediately. To avoid danger, this 
work must only be performed by the 
manufacturer’s service agent or a similarly 
qualified person. 



Keep the area above the cabinet—and around 
the exhaust opening—clear for air circulation 
and free from dust, lint and fluff. Do not use for 
storage. 



Do not use heat to dry articles containing foam 
rubber or similar textured rubberised materials. 
Instead, use the fan-only operation.  



Do not tamper with the controls. 



Do not install or store this cabinet where it will 
be exposed to weather. 



When using fabric softeners or antistatic 
agents, follow the product guidelines 
concerning their use. 



Do not dry articles that have been previously 
cleaned in, washed, soaked or splashed with 
petrol, or other flammable/ explosive 
substances, as they give off vapours that could 
ignite or explode. 



Check the exhaust ducting terminal grille for 
any blockage or build-up of lint. This must be 
cleaned regularly. 



The manufacturer accepts no liability for repairs 
carried out:- 

a)  by unauthorised personnel 

b)  with the use of non-standard parts 

THIS USER MANUAL 

NOTE.  

Keep this user 

manual so it is always 
available for future use. 

Summary of Contents for ETS-1700E

















Reviews: