background image

7 of 10

ISSUED: 09-30-11   SHEET #: 009-9056-5  (2014-04-08)

NOTE:

 "X" dimensions should be equal.

Installing Adapter Brackets to Flat Panel Display

To prevent scratching the display, set a cloth on a fl at, level surface that will support the weight of the display. Place 
display face side down. Refer to display manufacturers instructions or customer service, for removing any knobs, 
base, cover, or screw(s) on the back of the display to prepare mounting. These need to be removed to allow the 
adapter brackets (

F

) to be attached. Select the small, medium, large or extra large screws from the baffl ed fastener 

pack then attach adapter brackets to display following fi gure 8.1 or 8.2.

NOTE:

 Top and bottom mounting holes must be used for attaching adapter brackets. Verify that all holes are 

properly aligned, and then tighten screws using 4 mm security allen wrench (

BB

).

F

CENTER BRACKETS 

VERTICALLY ON BACK 

OF DISPLAY

X

X

8

Notes:

 

•  The number of fasteners used will vary, 

depending upon the type of display.

•  Multi-washers and spacers may not be 

used, depending upon the type of display.

•  Use the corresponding hole in the multi-  

washer that matches your screw size as 
shown.

MEDIUM HOLE FOR M5 SCREWS

SMALL HOLE FOR M4 SCREWS

LARGE HOLE FOR M6 SCREWS

MULTI-WASHER

NOTE: 

For 

fl at back displays

 proceed to step 

8

-1. For 

bump-out or recessed back display

 skip to step 

8

-2.

•  Tighten screws so adapter brackets are fi rmly attached. Do not tighten with excessive force. Overtightening can 

cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become 
detached.

 

Tighten to 40 in. • lb (4.5 N.M.) maximum torque.

•  If screws don't get three complete turns in the display inserts or if screws bottom out and adapter brackets are still 

not tightly secured, damage may oXur to display or product may fail.

 WARNING

Summary of Contents for SS560FK











Reviews: