PEELLE 224-EN Installation & Interface Manual Download Page 41

37

FREIGHT DOORS

I

CAR GATES

I

CAR ENCLOSURES

T

ECHNICAL 

S

UPPORT

 1-800-787-5020 ext 275

THE PEELLE COMPANY

®

Guide No.

Date: 

224-EN

WIRELESS CONTROLLER 

INSTALLATION & INTERFACE GUIDE

May 13 / 2021

10.0  EC DECLARATION OF CONFORMITY

Manufacturer:

The Peelle Company Ltd.

195 Sandalwood Pkwy W.

Brampton, Ontario  L7A 1J6

CANADA

We, The Peelle Company Limited of Brampton, Ontario, declare that the product designated 

below complies with the relevant fundamental requirements of Article 3 of the Lifts directive 

2014/33/EU insofar as the product is used as intended and the following standards applied:

Product: Wireless Freight Door Controller, 2.4GHz, 802.15.4 Transceiver Module

Manufactured by: The Peelle Company Ltd. Trade mark: Peelle

Model: WFDC 27451 Car Door, WFDC 27452 Landing Door

Environment of use: Residential, commercial and light industry

Standards:

-Lifts EN 81-20:2014 Safety rules for the construction and installation of lifts

EN 12015:2014 Electromagnetic compatibility – Emissions

EN 12016:2013 Electromagnetic compatibility – Immunity

EN 61000-6-1:2007 Electromagnetic compatibility (EMC)

-Telecommunication EN  50371, EN 301 489-1, EN 301 489-17, EN 300 440

Date of issue: MAY 2017

Place of issue: Brampton, Ontario, CA

Frank Leo P.Eng.

Engineering Manager

Summary of Contents for 224-EN











































Reviews: