manualshive.com logo in svg

Peavey PVX p 10, Manual

Share
Download
Peavey PVX p 10 Manual Download Page 45

Loudspeaker System Specifications 

43 

Sine wave Power*: 160 watts @ less than 1% distortion 
Tweeter - 120 watts peak dynamic power 
Sine wave Power*: 45 watts @ less than 1% distortion. 
 * 

Before DSP compression and limiting engages.

 

 

Electronic Input Impedance (Nominal

):  

Line:  20 k ohms balanced (1/4" and XLR), 15 k ohms unbalanced 1/4", 
6.4 k ohms 1/8" jack 
Mic:   2.7 k ohms balanced (XLR) No phantom power available. 
 

Input Sensitivity for Full Output (Channel Input Level knob full CW, Master 
DSP gain full-up, DSP CH1 or CH2 at 0 dB):

   

1 / 4” TRS /XLR combo jack: 0.50 V RMS 
See

 Level Control Adjustment 

section for more details under different channel 

and Main Gain settings. 
 

DSP Specifications:  

DSP Input and Output is at 48 kHz and 24 bits, internal 

processing is 56 bit double-precision.  Latency: 1.2 ms

 

 

Infrasonic filter protection:

 Minimum 36 dB/octave roll-off, 48 dB/octave roll-off 

with adjustable input filters engaged. 
 

Nominal Amplifier Frequency Response:

 +0, -3 dB from 20 Hz to 20 kHz 

 

Hum and Noise:

 Greater than 90 dB below rated power 

 

Overdrive Dynamic Range:

 Greater than 15 dB 

 

THD and IM:

 Typically less than 0.5 % 

 

Power requirements of Peavey 

PVX™p 10 Bluetooth® System:  

Nominal 100 Watts, 100-120 VAC 50-60 Hz 

Summary of Contents for PVX p 10














































Reviews:

No comments

Brands by name

Popular brands

Load more brands