manualshive.com logo in svg

Peavey PVX p 10, Manual

Share
Download
Peavey PVX p 10 Manual Download Page 44

Loudspeaker System Specifications 

42 

 

Crossover Slopes: 

Nominally 24 dB/octave (4th order) low pass, 24dB/octave (fourth order) high 
pass, both with driver EQ incorporated.  
  

Input Connections (Each, Channels 1 and 2): 

One combo female XLR and1/4" phone jack providing balanced line-level 
operation.  Mic/Line switch provides extra gain for microphone use. 
 

Input Connections (Channel 3): 

AUX is a 1/8" phone type jack.  Channel 3 is nominally the Bluetooth® signal 
source channel.  
 

Output Connection: 

 

One male XLR jack.  This jack is intended for the use of linking multiple 

PVX™p 

10

‘

s

 

in a line or to provide a feed to a powered subwoofer, or other electronics 

that needs to receive a full range version of the input signal.   
 

Enclosure Materials & Finish: 

Black injection-molded plastic with textured surface, black powder-coated 
perforated grilles. 
 

Mounting provisions: 

Unit has two sets of two M10 inserts, one pair on the top, and one pair on the 
bottom. 
Additional mounting points are a set of four M8 inserts on the top, and a set of 
four on the bottom, which use the Peavey VersaMount

™ 70 mounting bracket. 

Four rubber feet provide vibration free floor or stage use, and a molded-in stand 
mounting cup is on the bottom. 
 

Dimensions (H x W x D): 

Front: 
20.00 in. x 12.69 in. x 11.06 in. 
508 mm x 322 mm x 281 mm 
Rear: 
19.62 in. x 7.19 in. x 11.06 in. 
498 mm x 183 mm x 281 mm 
 
Net Weight:  
27 lbs.  (12.4 kg) 
 

ELECTRONICS AND AMPLIFIER SPECIFICATIONS 

 

Internal power amplifiers Power Ratings (@120 VAC line

):  

Total of 520 watts peak dynamic power 
Woofer - 400 watts peak dynamic power 

Summary of Contents for PVX p 10














































Reviews:

No comments

Brands by name

Popular brands

Load more brands