manualshive.com logo in svg

Peavey PVX p 10, Manual

Share
Download
Peavey PVX p 10 Manual Download Page 43

Loudspeaker System Specifications 

41 

A separate powder-coated metal grille shall be provided for horn and woofer 
protection. The cabinet shall incorporate a pole mount for speaker stand use, 
four tall sturdy rubber feet for floor standing use, and two sets of mounting point 
inserts on the top and bottom each, for flying use. 
The outside dimensions shall be: 20

.0” (50.8 cm) tall x 12.69” (32.2 cm) wide x 

11.06

” (28.1 cm) deep, and the weight shall be 27 lbs. (12.4 kg).  Power 

requirements shall be: 100  Watts nominal, 100-120 VAC, 50/60 Hz Domestic 
and 220-240 VAC, 50/60 Hz (Export). The loudspeaker system shall be called a 
Peavey 

PVX™p 10 Bluetooth®. 

 
 

GENERAL SPECIFICATIONS 

 

Frequency Range

, 1 meter on-axis, swept-sine in ½ Space environment: 

52 Hz to 20 kHz 

 

 

Frequency Response, 1 meter on-axis, swept-sine in anechoic 
environment: 

65 Hz to 20 kHz (±3 dB) 
 

Usable Low Frequency limit 

(-10 dB point anechoic):

 

54 Hz 
 

 

Nominal sensitivity 

(1W @1M, swept sine input in anechoic environment):

 

96  dB (average) 
 

Maximum Sound Pressure Level (1 meter): 

123 dB SPL peak with music 
 

Radiation Angle measured at -6 dB point of polar response: 

Nominal:

  

100 degrees horizontal X 60 degrees vertical 

(Axis of the vertical main polar lobe is angled down 10 degrees, resulting in the 
angular pattern with respect to straight ahead being +20, -40 degrees) 
 

Transducer Complement: 

Heavy-duty 10

” woofer with 2 3/8” voice coil & 50 oz. magnet 

RX™10 1.0”

 

titanium diaphragm dynamic compression driver 

 

Box Tuning Frequency: 

75 Hz 
 

Electroacoustic crossover frequency:

  2,000 Hz 

 

Crossover type: 

Advanced DSP based filter also providing driver EQ, level matching, bass boost, 
limiting, compression and subsonic filtering. 

Summary of Contents for PVX p 10














































Reviews:

No comments

Brands by name

Popular brands

Load more brands