PeakTech TK-100 Operation Manual Download Page 7

Page: 7 / 16

Introduction

The TK-60, TK-100, TK-250 and TK-250/100 are passive high impedance

oscilloscope probes designed and calibrated for use on instruments having
an in-put impedance of 1 M

Ω

shunted by 20 pF. However, it may be

compensated for use with instruments having an input capacitance of 10-35

pF. The probe incorporates a three position slide switch in the head, which

selects attenuation of x1, x10 or a ground reference position (not PeakTech

TK-250/100)

Safety instructions

This probe has been designed for use on low energy systems only as defined

in category II of EN 61010-031. The probe should only be used with
oscilloscopes, that have a grounded BNC connector. Do not attempt to make

measurements where the ground lead or oscilloscope input is raised above

ground potential. If differential measurements are required, use a dual

channel scope in the differential mode with two probes or use a differential

probe.

REF-position

The oscilloscope probes TK-60, TK-100 and TK-250 are provided with a

refer-ence-position. The oscilloscope-probe tip is disconnected and the

oscilloscope-input is grounded.

Maintenance

Before dismantling any part of the probe, make sure it is disconnected from

any voltage source. The measurement tip is replaceable. The probe head can

be detached from the cable assembly by unplugging the push fit BNC

connector on the probe head. To replace a broken tip, hold the black

insulating part of the tip with plier and screw it away from the probe head.

Replace with a new tip taking care to align with the inner contact.

Compensation Adjustment

In order to obtain the correct division ratio with each oscilloscope, the

attenuation network needs to be adjusted. To compensate the probe to your

oscilloscope, apply a 1 kHz square wave to the probe tip, or connect to the

cal socket on the oscilloscope to display a few cycles of the waveform and

adjust the trimmer located in the BNC-plug for a flat topped square wave.

-6-

Summary of Contents for TK-100

















Search results

Summary of Contents for TK-100

Reviews:

Brands by name

Popular brands

PeakTech TK-100, Operation Manual

Search results

Summary of Contents for TK-100

Reviews:

Brands by name

Popular brands