Peak Pilates MVe Chair Assembly & User'S Manual Download Page 5

Page: 5 / 10

6. Place the Front Leg over its holes near the front edge of the Seat. Again the Leg is sy-

metric. Start one M10 x 1.5p x 25mm long sockethead cap screw in each of its three holes.

Thread the screws but do not fully tighten at this time.

7. Pick up the Base being careful to not allow the Foot Pedal to swing freely.

8. Place the Base upside down on top of the Legs. Be sure that the Base lies in the notches

at the ends of each of the Legs. Align the holes of the Base with the threaded inserts located

inside of the ends of the Legs. Fasten using the (4) M10 x 1.5p x 61mm long socket head cap

screws. Do not fully tighten any of the screws until all four are started.

9. Fully tighten the 6 screws securing the Legs to the Seat Cushion and the 4 screws secur-

ing the Base to the Legs.

10. While holding the Foot Pedal, carefully turn the Chair over on to its Base.

Note: Before assembling the Springs, verify that the Foot Pedal is in the exercise position

and not the stacking position. If you are not sure how to check the position of the Foot

Pedal, see the “Users Guide” below. Also, move the Spring Adjustment Slider/Silders to

Position 4, the top hole on the Slider Guide Bar.

11. The Springs will be assembled to the Spring Adjustment Slider first. With the Foot Pedal

all of the way down against the floor, insert the loop at the end of each of the Springs into a

notch in the flange of the Spring Adjustment Slider. Insert the Retaining Pin into the cylindri-

cal end of the flange in the direction shown.

Note: The Split-Pedal option uses (1) short Retaining Pin for each Spring Adjustment Slider.

12. Locate the groove at the end of the Retaining Pin. Place the E-Clip so that its “ears” are

within the groove.

Note: The Split-Pedal option uses two E-Clips.

Summary of Contents for MVe Chair










