background image

 

10 

Battery Charging:

 

 
Use only approved Peak Beam chargers.  Improperly charging a battery may reduce 
service life and, in extreme cases, may cause the product to flame or leak. 
 

Warning: Never charge a COLD battery that is cooled below  32°F (0°C).

 Allow 

battery to return to room temperature first before connecting it to charger. 

 

Charging with MBP-3205 or MBP-3230 Chargers: 

1.

 

To charge battery from a 100-240VAC Power Source,

 locate the MBP-3205 

AC  Charger.    Connect  charger’s  power  cord  to  a  100-240VAC  power  source.  
Connect charger to battery.   

2.

 

To charge battery from a 12VDC Vehicle,

 locate the MBP-3230 DC Charger.  

Connect  charger’s  12V  cigarette  lighter  plug  to  vehicle’s  12V  receptacle.  
Connect charger to battery. 

3.

 

Battery  will  automatically  begin  to  charge.

    Charger’s  LED  will  turn 

RED

 

during  charging  and  will  turn 

GREEN

 

when  charge  is  complete.    The  MBP-

3205 AC Charger’s LED may pulse green during final charge stage. 

4.

 

Do not leave battery connected to charger for longer than 24 hours.  

 
Charging with MBP-3200 Series Smart AC/DC LiFePO

4

 

Chargers: 

1.

 

Locate  the  MBP-3200  Smart  Charger  and  compatible  charging  adapter 

(see 

adapters on page 8).  

Connect adapter to appropriate input power source.

 

2.

 

Plug the  female  end  of the  charging adapter into the  charger’s input connector.  
Charger LED will turn steady 

RED

 

when input power is connected.

 

3.

 

Connect charger pigtail to battery.  

Battery will automatically begin to charge.

  

Charger LED will turn 

AMBER

 during charge. LED will pulse 

GREEN

 

at 99% 

of  charge  and  turn  steady 

GREEN

 

when  charge  is  complete.   

Battery  may  be 

disconnected and used at any point during charge, but it is recommended that a 
full charge cycle be completed periodically to maintain optimum battery health. 

 
LED Status Indications for MBP-3200 Series Smart Charger: 

Charger LED Behavior 

Indication 

Steady Red

 

Input power is connected 

Steady Amber 

Battery is charging 

Pulsing Green 

Battery is at 99% of charge 

Steady Green 

Charge is complete 

Flashing Red 

Incorrect input voltage to charger 

Pulsing Red 

Defective battery OR charger output is shorted 

Red/Amber Flash

 

Charger and/or battery is too hot or too cold to charge 

Green/Amber Flash 

Battery cells are being balanced 

Erratic Charger Display

 

Bad/loose connection to battery OR defective charger 

 

 

Summary of Contents for MAXA BEAM MBPKG-E























Reviews: