background image

 

   19                                                                       20

 

Note:   

 

Position the inductive pick-up as far away from the distributor and 

the exhaust manifold as possible

 

  Position the inductive pick-up within six inches of the spark plug or 

move it to another plug wire if no reading or an erratic reading is 
received. 

 
RPM 4

 

:

  For RPM of 4-stroke engines which have 1 ignition on every 

4 engine strokes 

 
RPM 2 : 

For RPM of DIS  (Distributorless  Ignition  System)  & 2-stroke 
engines which have 1 ignition on every 2 engine strokes 

PLEASE  NOTE

 

  THE RPM PICK-UP HAS AN ADJUSTABLE SENSITIVITY  SWITCH THAT CAN 

ALSO BE USED TO CORRECT AN UNSTABLE READING.

 

As you are measuring, keep the meter away from the engine to ensure 

a stable reading. 

 

General Specifications 

The instrument complies with: 

IEC 1010-1

 

EN61010-1. 

Insulation: 

Class2, Double insulation. 

Overvoltage category: 

CATIII1000V/CATIV600V. 

Display:

 4000 counts LCD display with function indication. 

Polarity:

 Automatic, (-) negative polarity indication. 

Overrange:

 “OL” mark indication. 

Low battery indication:

  The “   ” is displayed when the battery 

voltage drops below the operating level. 

Measurement rate: 

2 times per second, nominal. 

Auto power off:

  Meter automatically shuts down after approx. 30 

minutes of inactivity. 

Operating environment:

 0ºC to 50

C (32

F to 122

F) 

                        at < 70 % relative humidity. 

Storage temperature:

 -20

C to 60

C (-4

F to 140

F) at < 80 % relative 

humidity. 

For inside use, max height: 

2000m 

Pollution degree:

 2

 

Power:

 One 9V battery , NEDA 1604, IEC 6F22. 

Dimensions:

 167 (H) x 79 (W) x50 (D) mm 

Weight: Approx.:

 300g.

 

Accuracy and Resolution Specifications 

*Accuracy is given as

±

([X% of reading]

±

[number of least  significant 

digits]) at 18

C to 28

C (65

F to 83

F), with relative humidity up to 70%. 

 

RPM

 (Tach) 

Range 

Resolution 

Accuracy 

 

RPM 4 

600~4000 

RPM 

1 RPM 

 
 
 
 
+2 % of rdg + 4 dgts 

1000~12000 

RPM 
(X10 RPM) 

10 RPM 

RPM 2/DIS 

300~4000 

RPM 

1 RPM 

1000~6000 

RPM 
(X10 RPM) 

10 RPM 

Effect Reading: >600 RPM 

 

DEWLL ANGLE

 

Cylinder 

Range 

Resolution 

Accuracy 

4CYL 

0~90.0

°

 

0.1

°

 

+2.0% of rdg + 4 dgts 

5CYL 

0~72.0

°

 

6CYL 

0~60.0

°

 

8CYL 

0~45.0

°

 

 

DC Voltage

   

Range 

Resolution 

Accuracy 

400.0mV 

0.1mV 

+0.5% of rdg + 3 dgts 

4.000V 

1mV 

 
+1.5% of rdg + 2 dgts 

40.00V 

10mV 

400.0V 

100mV 

600V 

1V 

+1.8% of rdg + 2 dgts 

Input Impedance: 10MΩ 

 

Summary of Contents for DM-930















Reviews: