manualshive.com logo in svg

PCM SAL-DLG FIREWOR-X-TEND, Building Instructions

Share
Download
PCM SAL-DLG FIREWOR-X-TEND Building Instructions Download Page 8

Firewor-X-tend Building instruction                                                                                                        January 2009                             

5.4 Installation of the elevator 

Fix the 

carbon rod (2mm)

 with superglue 

in the rudder

. 

he elevator will keep the distance between the two carbon 

 

evertheless, 

check the elevator for free movability

. If 

 

 

Now you can mount the elevator.  
 
T
rods. If you move the spring without the elevator mounted, 
the spring may disappear inside the rudder. Only when the 
elevator is mounted, the spring will move along the track cut
out.  
 
N
necessary, enlarge the hole in the rudder. 

 

You can stick the 2 halves of the elevator to each other 

on 

the leading edge

 with an 

adhesive tape

 to avoid 

unintended demounting. 

 
 

www.pcm.at                                                                                                                                                            

8 

Summary of Contents for SAL-DLG FIREWOR-X-TEND



















Reviews:

No comments

Brands by name

Popular brands

Load more brands