manualshive.com logo in svg

PCM SAL-DLG FIREWOR-X-TEND, Building Instructions

Share
Download
PCM SAL-DLG FIREWOR-X-TEND Building Instructions Download Page 4

Firewor-X-tend Building instruction                                                                                                        January 2009                             

4.  Settings for the first flight

 

 

 

Centre of gravity: 65mm (62-70mm) 

(measure from the leading edge of the wing to the back) 

 

 

Ailerons 

(measure near fuselage)

 

 

Flaps negative (start, speed) 

(measure near fuselage)

 

 

Flaps positive (thermal) 

(measure near fuselage)

 

 

Landing position 

(measure near fuselage)

 

 

Snap Flap 

(measure near fuselage)

 

 

Rudder 

(measure at deepest point) 

 

Angle of attack of elevator

 (for first flight): set elevator parallel to axis of boom, slightly pulled 

(1,5mm) 

www.pcm.at                                                                                                                                                            

4 

Summary of Contents for SAL-DLG FIREWOR-X-TEND



















Reviews:

No comments

Brands by name

Popular brands

Load more brands