manualshive.com logo in svg

PCM SAL-DLG FIREWOR-X-TEND, Building Instructions

Share
Download
PCM SAL-DLG FIREWOR-X-TEND Building Instructions Download Page 16

Firewor-X-tend Building instruction                                                                                                        January 2009                             

10.  Installation of antenna 

 
In order to have an undisturbed reception a 

part of the 

antenna

 must be situated 

outside the model

.  

 
An easy solution is to 

fix the antenna to the end of the 

elevator

. Lead the antenna inside the fuse behind the wing 

and then leave the fuselage.  

 

Another possibility is to lay the antenna 

inside the gap of 

the aileron

. For improving reception on 

carbon wings

 you 

can solder the antenna to a steel wire, d=0,3mm, which you 
fix at the end of the wing and let stand out to the back about 
10-15cm. 

 

Always 

TEST THE RECEPTION

 on ground before you 

fly! 

 

 
 

www.pcm.at                                                                                                                                                            

16 

Summary of Contents for SAL-DLG FIREWOR-X-TEND



















Reviews:

No comments

Brands by name

Popular brands

Load more brands