PCM 2008 Catanium CES 6.0L ZR-409 Owner'S Operation And Maintenance Manual Download Page 5

Page: 5 / 93

L510010-11

INTRODUCTION

...............................................................................................................................

3-9

Registration Information (Warranty Registration Card is located at the back of this manual)

........................

3-Year Transferable Limited Warranty

.....................................................................................................

Federal/California Emission Control Warranty Statement

.........................................................................

PCM Inboard Marine Engine General Emissions Warranty Coverage

........................................................

Safety Information

................................................................................................................................

Replacement Parts

...............................................................................................................................

Safety Warnings

...................................................................................................................................

BOATING RESPONSIBILITIES

......................................................................................................

10-12

Carbon Monoxide Hazard

....................................................................................................................

Safe Boating Suggestions

...................................................................................................................

Water Wisdom

....................................................................................................................................

Operation and Maintenance

.................................................................................................................

Rules of the Road

...............................................................................................................................

ENGINE IDENTIFICATION

.............................................................................................................

13-14

Engine Identi

cation

............................................................................................................................

Owner Identi

cation and Registration Information

..................................................................................

Engine Model Identi

cation / Advisory

...................................................................................................

ELECTRONIC FUEL INJECTION INFORMATION

................................................................................

Electronic Fuel Injection System

..........................................................................................................

OPERATING INSTRUCTIONS

........................................................................................................

16-22

Engine Alarm System

..........................................................................................................................

Instrumentation

...................................................................................................................................

Electronic Speed Control

.....................................................................................................................

Starting Engine (Fuel Injected Engines)

................................................................................................

Shifting Transmission

..........................................................................................................................

Stopping Engine

.................................................................................................................................

Freezing Temperature Operation

..........................................................................................................

Operation in High Debris Areas

............................................................................................................

PCM Basic Cruise Speed Control System

........................................................................................

21-22

CONDITIONS AFFECTING OPERATION

........................................................................................

23-24

Trim and Weight Distribution

................................................................................................................

Boat Bottom

.......................................................................................................................................

Propeller Selection

..............................................................................................................................

ENGINE BREAK-IN PERIOD

..............................................................................................................

25-HOUR ENGINE INSPECTION

........................................................................................................

FUEL REQUIREMENTS

.....................................................................................................................

Gasoline Requirements

.......................................................................................................................

Gasoline Containing Alcohol

................................................................................................................

OIL REQUIREMENTS

........................................................................................................................

Engine Oil Recommendations

..............................................................................................................

Transmission and “V”-Drive Oil Requirements

.......................................................................................

ENGINE MAINTENANCE

...............................................................................................................

29-55

Engine Maintenance

...........................................................................................................................

Checking Fluid Levels

....................................................................................................................

29-31

Lubrication

.........................................................................................................................................

TABLE OF CONTENTS

Summary of Contents for 2008 Catanium CES 6.0L ZR-409






























































































Search results

Summary of Contents for 2008 Catanium CES 6.0L ZR-409

Reviews:

Related manuals for 2008 Catanium CES 6.0L ZR-409

Brands by name

Popular brands

PCM 2008 Catanium CES 6.0L ZR-409, Owner'S Operation And Maintenance Manual

Search results

Summary of Contents for 2008 Catanium CES 6.0L ZR-409

Reviews:

Related manuals for 2008 Catanium CES 6.0L ZR-409

Brands by name

Popular brands