manualshive.com logo in svg

PCB Piezotronics Larson Davis SoundAdvisor NMS044, Reference Manual

Share
Download
PCB Piezotronics Larson Davis SoundAdvisor NMS044 Reference Manual Download Page 17

NMS044 Reference Manual

Establishing Service for the Gateway

14

2.2.2 Installing the SIM Card

With the system powered off, install the SIM card by following these steps:

Step 1.

Using the provided #2 Phillips head screw driver, remove the 2 screws holding

the gateway to the case plate, as shown in 

Figure 2-5

.

Step 2.

Make note of the unique password on the label on the bottom of the RV50X

Figure 2-5  

Removing the Gateway From the Case Plate

Step 3.

Using the #0 screwdriver, remove the 2 screws holding the front SIM card door,

shown in 

Figure 2-6

. 

Figure 2-6  

RV50X Sim Card Door Removed

Step 4.

Insert the SIM card into to the top slot until it clicks.

Step 5.

Replace the SIM card door and screws.

Step 6.

Remount the RV50X in the case and hand-tighten the 2 case plate screws.

Summary of Contents for Larson Davis SoundAdvisor NMS044




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands