PCB Piezotronics Larson Davis EPS044 Reference Manual Download Page 5

Page: 5 / 57

NMS044 Reference Manual Rev E

Overview

1-1

Module 1

System Overview

Overview ..............................................................................................................................1-1

1.2

EPS/NMS044 Features .........................................................................................................1-2

1.3

Components ........................................................................................................................1-2

1.4

Optional Accessories ...........................................................................................................1-7

1.5

Wiring Diagrams ..................................................................................................................1-7

1.1 Overview

The SoundAdvisor Model NMS044 noise monitoring system (NMS044, system) is

the practical solution to long-term or short-term, unattended sound level

monitoring. Power is supplied by a 12 V battery, and the system is charged by a

solar panel, chosen specifically for the area sunlight availability. It is lightweight,

as little as 50 lbs, so one person can carry to a site and setup within a few

minutes.

FIGURE 1-1

NMS044 Overview

Environmentally

protected

microphone and

preamplifier

Telescoping pole keeps

the microphone away

from any sound

reflections in the area.

Do not place near trees

or other large elements.

The outdoor case

protects and securely

fits the battery,

charge controller,

antennas, modem,

and sound level

meter

Place the solar panel

facing the sun’s main

trajectory with no

obstructions.

Environmentally

protected

microphone and

preamplifier

Summary of Contents for Larson Davis EPS044


























































Search results

Summary of Contents for Larson Davis EPS044

Reviews:

Related manuals for Larson Davis EPS044

Brands by name

Popular brands

PCB Piezotronics Larson Davis EPS044, Reference Manual

Search results

Summary of Contents for Larson Davis EPS044

Reviews:

Related manuals for Larson Davis EPS044

Brands by name

Popular brands