background image

 

PAGE 14 

 

 

Warranty 

IMI instrumentation is warranted against defective material workmanship for 1 year unless otherwise expressly 

specified.  Damage to instruments caused by incorrect power or misapplication, is not covered by warranty.  

If 

there are any questions regarding power, intended application, or general usage, please consult with your local 

sales contact or distributor.  

Batteries or expendable hardware items are not covered by warranty. 

 

Service 

Because of the sophisticated nature of IMI instrumentation, field repair is typically 

NOT

 recommended and may 

void any warranty.  If factory service is required, return the instrumentation according to the “Return Procedure” 

stated below.  

A repair and/or replacement quotation will be provided prior to servicing at no charge.

  Before 

returning the unit, please consult a factory IMI applications engineer concerning the situation as certain problems 

can often be corrected with simple on-site procedures. 

 

Return procedure 

To expedite returned instrumentation, contact a factory IMI applications engineer for RETURN MATERIAL 

AUTHORIZATION (RMA) NUMBER.

  Please have information available such as model and serial number.  Also, 

to insure efficient service, 

provide a written description of the symptoms and problems with the equipment to a 

local sales representative or distributor, or contact IMI if none are located in your area. 

 

Customers outside the U.S. should consult their local IMI distributor for information on returning equipment.  For 

exceptions, please contact that International Sales department at IMI to request shipping instructions and an 

RMA.  For assistance, please call (716) 684-0003, or fax us at (716) 684-3823.  You may also receive assistance 

via e-mail at 

[email protected]

 or visit our website at 

www.pcb.com

 

Customer Service 

IMI, a division of PCB Piezotronics, guarantees 

Total Customer Satisfaction

.  If, at any time, for any reason, you 

are not completely satisfied with any IMI product, IMI will repair, replace or exchange it at no charge.  You may 

also choose to have your purchase price refunded. 

 

IMI offers to all customers, at no charge, 24-hour phone support.  This service makes product or application 

support available to our customers, day or night, seven days a week.  When unforeseen problems or emergency 

situations arise, call the 

IMI Hot Line at (716) 684-0003

, and an application specialist will assist you.

 

Summary of Contents for IMI SENSORS 640B11






















Reviews: