background image

 

PAGE 13 

 

 

Warning 1 

– ESD sensitivity 

 

 

The power supply/signal conditioner should not be opened by anyone other than qualified service 

personnel.  

This product is intended for use by qualified personnel who recognize shock hazards and are familiar 

with the safety precautions required to avoid injury. 

 

Warning 2 

– ESD sensitivity 

 

This equipment is designed with user safety in mind; however, the protection provided by the equipment may be 

impaired if the equipment is used in a manner not specified by PCB Piezotronics, Inc. 

 

Caution 1 

– ESD sensitivity 

 

Cables can kill your equipment.  

High voltage electrostatic discharge (ESD) can damage electrical devices.  

Similar to a capacitor, a cable can hold a charge caused by triboelectric transfer, such as that which occurs in the 

following: 

 

 

Laying on and moving across a rug,  

 

Any movement through air,  

 

The action of rolling out a cable, and/or 

 

Contact with a non-grounded person.

 

 

 

The solution for product safety: 

 

 

Connect the cables only with the AC power off. 

 

Temporarily “short” the end of the cable before attaching it to any signal input or output.  

 

Caution 2 

– ESD sensitivity 

 

ESD considerations should be made prior to performing any internal adjustments on the equipment.  

Any 

piece of electronic equipment is vulnerable to ESD when opened for adjustments.  Internal adjustments should 

therefore be done ONLY at an ESD-safe work area.  Many products have ESD protection, but the level of 

protection may be exceeded by extremely high voltage. 

  

Summary of Contents for IMI SENSORS 640B11






















Reviews: