background image

AN1173-AE

Net2

5

Cover plates

Door Widths

If a slimline electronic door handle is being replaced with the PaxLock Pro, cover plates are available to 
cover any unused holes in the door. The cover plates can be fitted over the top of the PaxLock Pro and 
secured with 4 supplied wood screws; one in each corner. 

The appropriate cover plate will need to be ordered depending on whether a key override is present and 
matched to the centre measurement of the lockset.

Notes will need to be taken on the door thicknesses across a potential site, this information will be required 
when ordering the PaxLock Pro. 

 

• 

Out of the box the PaxLock Pro will work with 

40-44mm

 door widths.

 

• 

Before installing a PaxLock Pro on a unit that is 

35-37mm

, both the spindle and 

 

 

through door bolts will need to be cut down to the correct length as per the 

 

 

drilling template. 

 

• 

For door widths of 

50-54mm

 or 

57-62mm

, a separate Wide Door kit will need to be  

 

   purchased.

Once you are happy the site is suitable for the PaxLock Pro you will need to ensure you have the right 
information to order the correct products. 

There are 4 sales codes to choose from depending on whether you want an internal or external PaxLock 
Pro in either black or white. 

Ordering the right kit

When choosing the external version, it is important to note that only the external side of the lockset is IP 
rated, meaning the PaxLock Pro should never be installed externally where the whole unit is exposed to 
the elements. 

Also see:  Cover plates dimensional drawing < 

paxton.info/3560 

>

BS EN179 is a standard for devices to be used in emergency situations where people are familiar with the 
emergency exit and its hardware, therefore a panic situation is unlikely to develop. This means lever handle 
operated escape mortice locks or push pads may be used. 

BS EN179 – Emergency Exit devices for use on escape routes 

The PaxLock Pro is certified to the BS EN179 standard meaning the product is suitable for use 
on emergency exits in areas where a panic situation is unlikely to develop.

!

The PaxLock Pro must be used with the PaxLock Pro - Euro, EN179 kit or the door system will not be compliant 
to BS EN179. 

Summary of Contents for PaxLock Pro











Reviews: