background image

Owners Guide

Read all information and instructions, including Gaslight Warning Tag attached to light,

before installation or use.  Retain this guide for future reference.

Indoor Gaslights

Information and Instructions

Model 9 for homes, cottages, and cabins (pre-formed mantle).

Model 9T must be used for recreational vehicles (tie-on mantle)

The design of Model 9 and 9T is C.S.A. certified.  Installation must
conform with local codes or, in the absence of local codes, with the
National Fuel Gas Code, ANSI Z223.1 (latest edition), and/or with
CAN1-B149.2 (latest edition) installation code for propane and butane
burning appliances and equipment, and local codes.

IMPORTANT INFORMATION FOR USING PAULIN INDOOR GASLIGHTS

Use Gaslights only for purposes of illumination.  Installation and repair of equipment that operates on
propane or butane gas is a job for experts.  Do not attempt to install or repair your gaslight unless you
have been thoroughly trained and are experienced in such matters.  If your gaslight appears to be mal-
functioning, turn it to the “OFF” position and immediately contact your local dealer or the Paulin factory.

After installation and before use, have qualified gas personnel
approve your installation and check for gas leaks using a leak
detector.  Tubing, fittings, gaslight valve, and any other gas
transporting component should be checked.  Subjecting
valve assembly to testing pressures in excess of 6 PSI
can damage sealing grease which can cause leaks and
voids warranty.

Use your gaslight in vented rooms only.
Carbon monoxide is produced by the incomplete
combustion of fuel.

Attention Installer:

C.S.A. requires that you leave these instructions
with the appliance for the consumer.

Caution

If you smell gas:

1.  Shut off gas to appliance.
2.  Open windows
3.  Don’t touch electrical switches
4.  Extinguish any open flame.
5.  Immediately call your gas supplier.

DO NOT STORE OR USE GASOLINE

OR OTHER FLAMMABLE VAPORS
AND LIQUIDS IN THE VICINITY OF

THIS OR ANY OTHER APPLIANCE.

Summary of Contents for Model 9









Reviews: