920-0211-01 Rev. C
Page 1 of 8
IMPORTANT!
Read all instructions before installing and using. Installer: This manual must be delivered to the end user.
Contents:
1 X HIDE-A-LED head with built-in power module and cable
1 X Mounting Gasket
2 X #6 X 1/2” Screws
1 X Bezel
Installation & Mounting:
Important!
This unit is a safety device, and it must be connected to its own separate, fused power point to assure its
continued operation should any other
electrical accessory fail.
Before installation, examine the LED heads for transit damage. Do not use damaged or broken parts.
The 9014 Series Hide-A-LED™ provides exceptional warning capability in a compact light that
can be either mounted inside a head/tail light casing or surface mounted using the included
bezel. Using 6 high intensity LEDs the 9014 Series features 12 or 24 VDC operation, 16 flash
patterns, the ability to synchronize with additional units and a 9’ cable.
Installation Instructions
9014
1. Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices are essential to ensure
the safety of you and those you are seeking to protect.
2. Exercise caution when working with live electrical connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high current arcing,
which can cause personal injury and/or severe vehicle damage, including fire.
4. Proper placement and installation are vital to the performance of this warning device. Install this product so that output performance of the
system is maximized and the controls are placed within convenient reach of the operator so that s/he can operate the system without losing
eye contact with the roadway.
5. Do not install this product or route any wires in the deployment area of an air bag. Equipment mounted or located in an air bag deployment
area may reduce the effectiveness of the air bag or become a projectile that could cause serious personal injury or death. Refer to the
vehicle owner’s manual for the air bag deployment area. It is the responsibility of the user/operator to determine a suitable mounting location
ensuring the safety of all passengers inside the vehicle particularly avoiding areas of potential head impact.
6. It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In use, the vehicle operator
should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open trunks or compartment doors), people,
vehicles or other obstructions.
7. The use of this or any other warning device does not ensure all drivers can or will observe or react to a warning signal. Never take the right-
of-way for granted. It is your responsibility to be sure you can proceed safely before entering an intersection, driving against traffic, respond
-
ing at a high rate of speed, or walking on or around traffic lanes.
8. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying all laws regarding
warning signal devices. Therefore, the user should check all applicable city, state, and federal laws and regulations. The manufacturer as-
sumes no liability for any loss resulting from the use of this warning device.
Do not install and/or operate this safety product unless you have read and understand the safety information
contained
Failure to install or use this product according to manufacturers recommendations may result in property damage, serious injury, and/or death to
those you are seeking to protect!
!
WARNING!
Size:
0.87H x Dia. 1.51
Input Voltage: 12/24 VDC
Current Draw: 0.7A Max
Operating temperature range: -30 to +50ºC
Lumens:
9014A(Amber) 200
9014B(Blue)
100
9014R(Red)
200
9014C(Clear)460
Specifications:
Lamp Mounting:
Pick a location in the vehicle lamp housing that is at least 1” away from any
existing bulbs. Drill 1” hole in vehicle lamp reflector housing with hole saw.
Mark the two screw hole locations and drill with 3/32” bit. Install the LED
head into lamp housing with gasket as shown in Figure 1. Use silicone RTV
on the screws to seal the threads.Strap the driver module to a nearby wire
harness or body structure. Make electrical connections as described below.
Surface Mounting:
Mark and drill mounting hole locations in mounting surface. Make the
electrical connections described below and feed the driver module through
the mounting hole. Silicone RTV sealant should be used around the
mounting and screw holes. Install the bezel using the two screws provided.
LAMP MOUNTING
DO NOT USE LED HEAD
WITHOUT DRIVER MODULE!
3.12”
[79.25]
0.345”
[8.75]
1.505”
[38.23]
0.175”
[4.45]
0.695”
[17.65]
DRIVER MODULE
1.0”
[25.40]
1.28”
[32.51]
0.094”
[2.38]
SCREWS
GASKET
MOUNTING
SURFACE
MOUNTING HOLE
3/32” DRILL
The LED heatsink will get hot during
operation but will NOT melt any of the
plastic parts of the lens assembly.
DO NOT TOUCH the heatsink
during operation.
SURFACE MOUNTING
DO NOT USE LED HEAD
WITHOUT DRIVER MODULE!
0.575” [14.61]
1.65” [41.91]
DRIVER MODULE
MOUNTING SURFACE
0.688”
[17.46]
1.8”
[45.72]
0.094”
[2.38]
2.27”
[57.66]
BEZEL
SCREWS
MOUNTING HOLE
BEZEL OUTLINE
3/32” DRILL
FIGURE 1
FIGURE 2
