background image

  5

0 Preface 

 Validity 

This document applies to the following unit types: 

  FOCUS 200 Base series (Zehnder Focus 200 Base series) 

All the units in the FOCUS 200 Base series are referred to below using the generic product name FOCUS, except 
where it is necessary to distinguish between specific types. 
This manual deals with the various design variants of the FOCUS heat recovery unit. Possible accessories are only 
described to the extent necessary for appropriate operation of the unit. Please refer to the respective instructions for 
further information on accessory parts. 

  Target group and standard operation 

This manual is for users and qualified personnel. The activities are only allowed to be carried out by appropriately 
trained personnel who are sufficiently qualified for the respective work involved. 

 Qualification 

of target group 

0.2.1.1 Users 

Users must be instructed by qualified personnel as follows: 

 

Instruction in hazards when handling electrical devices 

 

Instruction in the system´s operation 

 

Instruction in the maintenance of the FOCUS unit 

 

Knowledge of and compliance with this manual, including all safety instructions 

0.2.1.2 Qualified 

personnel 

Qualified personnel must have the following qualifications: 

 

Training in dealing with hazards and risks when installing and operating electrical devices 

 

Training for the installation and commissioning of electrical devices 

 

Knowledge of and compliance with the locally applicable building, safety and installation regulations of the 
relevant local authorities or municipalities, the regulations of the water and electric utilities and other official 
regulations and guidelines 

 

Knowledge of and compliance with this document, including all safety instructions 

Unless otherwise stated in this manual, only a recognised qualified person is authorised to install, connect up, 
commission and to service the FOCUS unit. 

 

Standard operation of the unit 

This unit can be used by children aged 8 and over and also persons with reduced physical, sensory or mental abilities 
or a lack of experience and knowledge provided that they are under supervision or have been instructed on the safe 
use of the unit and understand the risks that result from it. Children must not play with the unit. Children must not carry 
out cleaning and user maintenance without supervision. 

1 Introduction 

The FOCUS unit is built to the current state of the art and the recognised safety regulations. The unit is subject to 
continuous improvement and development. This is why it is possible for your unit to deviate slightly from the description. 

 Proper 

use 

 Ventilation 

unit 

The FOCUS unit can be used for forced ventilation in homes and offices (and also in industrial buildings subject to 
certain restrictions). Any other type of use is considered as misuse.

 

Extreme conditions (e.g. salty air or air polluted 

with chlorine) can damage the unit. For reasons of safety, it is prohibited to modify the product or to install components 
that are not explicitly recommended or distributed by PAUL Wärmerückgewinnung GmbH for this product. 

 Control 

panel 

The external control panel allows you to operate the system from a central location. The control panel is only suitable 
for use in indoor areas.  

Summary of Contents for FOCUS 200 Base Series








































Reviews: