background image

4.2.2  Novell Configuration

The second option on the Available Configuration Options screen

lets you enter information to configure the Print Server to work in a
standard Novell environment.  Any of these fields may be edited.

4.2.3  Advanced Novell Configuration

The third option on the Available Configuration Options screen is

“Advanced Novell”.  This is UCONNECT’s alternative to the
PCONSOLE print queue utility.  Advanced Novell lets you point a
particular print server to specific file servers and print queues.  This is
done in two steps:

1) When you select the Advanced Novell option, you will be prompted to
supply a print server to configure.  Use the arrow and [esc] keys to
scroll and select the print server you wish to configure.  Then press
[ENTER].

2) Once you have selected a print server to configure, you will receive
the Advanced Novell Configuration screen, where you can point the
print server to particular file servers and print queues.

4.2.4  TCP/IP Configuration

The fourth option on the Available Configuration Options screen lets

you configure the Print Server to work in a Novell network running
TCP/IP.  Remember:  You cannot run a Unix session using
UCONNECT.   See Section 5.0 for TCP/IP operation.

4.2.5  Personal Netware Configuration

The fifth option on the Available Configuration Options screen lets

you configure the Print Server to work with Personal Netware.

15

16

Warning!  Contact your Novell Administrator if you are unfamiliar
with Novell setup procedures.

Summary of Contents for PeNet 2127

















Reviews: