5
6
2.0 GENERAL INFORMATION
Thank you for your purchase of this Patton Electronics product.
This product has been thoroughly inspected and tested and is warrant-
ed for One Year parts and labor. If any questions arise during installa-
tion or use of the unit, contact Patton Electronics Technical Services at
(301) 975-1007.
2.1 FEATURES
• Terminates T1/FT1 Circuits over a 4-Wire RJ-48C interface
• 10Base-T Ethernet bridge
• PPP (Point to Point Protocol, RFC 1661) with Bridge Control
Protocol (RFC 1638)
• Unstructured Rates at 1.544 Mbps
• D4 or ESF Framing Modes
• Supports AMI or B8ZS/B7ZS Line Coding
• Configuration via Software Control Port or Internal DIP Switches
• Six Easy-to-Read LED Indicators Monitor Data & Diagnostics
• Internal or Receive Recover Clocking
• Also Operates as a High-Speed Point-to-Point Modem
• Made in USA
2.2 GENERAL PRODUCT DESCRIPTION
The
NetLink-T1™ Model 2720/I is a single port T1/FT1 CSU/DSU
with Ethernet Bridging that provides high-speed LAN-to-WAN connec-
tivity. Plugging directly into the 10Base-T port of a hub or LAN switch,
the NetLink-T1™ provides T1 or FT1 access at connection data rates
of 1.544 Mbps, nx64, and nx56 (n=1 to 24 channels). The Netlink-
T1™ is an excellent choice for internet access as well as LAN-to-LAN
services.
The Netlink-T1™ provides digital access to a local WAN service
provider or directly between two facilities over a dedicated 4-Wire cir-
cuit. WAN bandwidth, framing and coding options are programmed via
externally accessible DIP switches or via a VT-100 type terminal using
the rear-mounted EIA-232 Control Port. Netlink-T1™ supports D4/ESF
framing options and AMI/B8ZS/B7ZS line coding. Netlink-T1™ also
supports a full range of system and diagnostic features that make sys-
tem setup easy. The Ethernet Bridge in this unit requires no configura-
tion at all.
The NetLink-T1™ provides T1 terminations over a modular RJ-48C
jack and comply with jitter tolerance capabilities as specified in ANSI
T1.403 and AT&T TR62411. External power options include 120VAC
and universal interface 100-240VAC. 48VDC and rack card versions
are also available.
3.
If your CSU causes harm to the telephone network, the telephone
company may temporarily discontinue your service. If possible, they will
notify you in advance, but if advance notice is not practical, you will be noti-
fied as soon as possible and will be informed of your right to file a complaint
with the FCC.
4.
If you experience trouble with the CSU, please contact Patton
Electronics, Co. for service or repairs. Repairs should be performed only by
Patton Electronics Co.
5.
You are required to notify the telephone company when you disconnect
the CSU from the network.
1.6 SERVICE INFORMATION
All warranty and non-warranty repairs must be returned freight prepaid
and insured to Patton Electronics. All returns must have a Return Materials
Authorization number on the outside of the shipping container. This number
may be obtained from Patton Electronics Technical Support at: tel: (301)
975-1007 email: [email protected] www: http://www.patton.com.
NOTE: Packages received without an RMA number will not be accepted.
Patton Electronics' technical staff is also available to answer any questions
that might arise concerning the installation or use of your Patton Model
2720. Technical Support hours: 8AM to 5PM EST, Monday through
Friday.
1.7 CE NOTICE
The CE symbol on your Patton Electronics equipment indicates that it
is in compliance with the Electromagnetic Compatibility (EMC) directive and
the Low Voltage Directive (LVD) of the European Union (EU). A Certificate
of Compliance is available by contacting Technical Support.
