background image

7

8

Switch S1-8:  Carrier Control Method

The setting for switch S1-8 determines whether the carrier is “con-

stantly on” or “controlled by RTS”.  This setting allows for operation in
switched carrier, multipoint and/or hardware handshaking applications.

S1-8

Setting

Off

Constantly on

On

Controlled by RTS

3.3   CONFIGURATION SWITCH SET “S2”

The DIP switches on S2 set word length, extended signaling rate,

RTS/CTS delay, V.52 and V.54 diagnostic test and 2- and 4-wire opera-
tion.

Switches S2-1 and S2-2:  Word Length

Switches S2-1 and S2-2 are set in combination to determine the

word length for asynchronous data, including the start and stop bits.  

S2-1

S2-2

Setting

Off

On

8 bits

On

On

9 bits

Off

Off

10 bits

On

Off

11 bits

Switch S2-3:  Extended Signaling Rate

The setting for switch S2-3 determines the range of variability the

Model 1065 Series “looks for” in asynchronous data rates (i.e., the
actual variance from a given frequency level the Model 1065 Series will
tolerate).

 S2-3

Setting

Off

-2.5% to +1%

On

-2.5% to +2.3%

Switches S2-4 and S2-5:  RTS/CTS Delay

The combined settings for switches S2-4 and S2-5 determine the

amount of delay between the time the unit “sees” RTS and when it
sends CTS.  Options are no delay, 7 ms and 53 ms.

S2-4

S2-5

Setting

On

On

7 ms

Off

On

53 ms 

On

Off

No delay

Off

Off

No delay

Switch S2-6 & S2-7:  2-Wire/4-Wire Mode Selection

The setting for switch S2-6 and S2-7 determines whether the

Model 1065 Series is operating in 2-wire or 4-wire mode.

S2-6

S2-7

Setting

On

On

4-wire (half duplex)

On

Off

4-wire (full duplex)

Off

On

2-wire (half duplex)

Switch S2-8:  V.54 Loopback Test Enable

This switch enables or disables V.54 looping in the Model 1065. 

S2-8

Setting

Off

V.54 Normal Operation Enabled

On

V.54 Testing Disabled

S2 SUMMARY TABLE

Position

Function

Factory Default

S2-1

Word Length

Off

S2-2

Word Length

Off

S2-3

Extended Signaling Rate

Off -2.5% to 1%

S2-4

RTS/CTS Delay

On

S2-5

RTS/CTS Delay

On

S2-6

2-Wire/4-Wire

On  (4-Wire) FDX

S2-7

2-Wire/4-Wire

Off  (4-Wire) FDX

S2-8

V.54

Off V.54 Enabled

}

}

7 ms

10 bits

Summary of Contents for Model 1065














Reviews: