Patton electronics 2703 User Manual Download Page 10

APPENDIX B

PATTON MODEL 2703 PIN CONFIGURATIONS

17

13- (CTS/) Clear to Send
12- (TC/) Transmit Clock
11- Not Used
10- (CD/) Carrier Detect
9- (RC/) Receive Clock
8- (CD) Carrier Detect
7- (SG) Signal Ground
6- (DSR) Data Set Ready
5- (CTS) Clear to Send
4- (RTS) Request to Send
3- (RD) Receive Data
2- (TD) Transmit Data
1- Shield

UNIVERSAL D-26 INTERFACE (DCE WIRING)

Not Used -26
Not Used -25
Not Used -24

Data Term Ready (DTR/) -23

Data Set Ready (DSR/) -22

Not Used -21

Data Term Ready (DTR) -20

Request to Send (RTS/) -19

Not Used -18

Receive Clock (RC) -17

Receive Data (RD/) -16

Transmit Clock (TC) -15

Transmit Data (TD/) -14

APPENDIX C

PATTON MODEL 2703 

FACTORY PARTS AND ACCESSORIES

C-1 Basic Standalone Units

The Patton Model 2703 standalone digital modem is available in

three versions, depending upon the power supply installed.  The
Standard and Universal Interface versions are supplied with a power
cord, 

which must be specified in the model number when ordering

.

The DC version is supplied without a power cord.  

All versions of the Model 2703 are supplied without a terminal

(DTE) interface cable.  This cable may be ordered separately, or may
be supplied by the user.

Standard power supply option, 
switchable between 115 and 230 VAC............................Model 2703/

Universal Interface power supply option,
operates in environments ranging from 
85 to 265 VAC ............................................................Model 2703-UI/

DC power supply option,
operates in 48 VDC environments, 
equipped with a 3-pin “terminal strip” 
for DC power connection ..............................................Model 2703-DC 

C-2 AC Power Cords

Power cord must be specified when ordering Models 2703 or

2703-UI.  If power cord is omitted, suffix “K” will be assigned.

Ordering Suffix (

)

Power Cord Description

A .....................................Continental Europe, CEE 7
C.....................................reserved, Australia, New Zealand
D.....................................United Kingdom
E .....................................reserved, Denmark
F .....................................reserved, France/Belgium
G.....................................reserved, India
H.....................................reserved, Israel
I ......................................reserved, Italy
J......................................reserved, Japan
K .....................................North America
L .....................................reserved, Switzerland

Example: 2703-UI/D = Universal Interface w/ UK power cord.

18

Summary of Contents for 2703












Reviews: