background image

3

1.3  RADIO AND TV INTERFERENCE

The Model 2090 Series generates and uses radio frequency energy,

and if not installed and used properly—that is, in strict accordance with
the manufacturer's instructions—may cause interference to radio and
television reception.  The Model 2090 Series has been tested and found
to comply with the limits for a Class A computing device in accordance
with the specifications in Subpart J of Part 15 of FCC rules, which are
designed to provide reasonable protection from such interference in a
commercial installation.  However, there is no guarantee that interference
will not occur in a particular installation.  If the Model 2090 Series does
cause interference to radio or television reception, which can be determined
by disconnecting the cables, the user is encouraged to try to correct
the interference by one or more of the following measures:  moving the
computing equipment away from the receiver, re-orienting the receiving
antenna, and/or plugging the receiving equipment into a different AC
outlet (such that the computing equipment and receiver are on different
branches).

4

1.4  SERVICE

All warranty and non-warranty repairs must be returned freight

prepaid and insured to Patton Electronics.  All returns must have a
Return Materials Authorization number on the outside of the shipping
container. This number may be obtained from Patton Electronics
Technical Support at: 

telephone:  (301) 975-1007
email:  [email protected]
web address: http://www.patton.com

NOTE: Packages received without an RMA number will not be
accepted.

Patton Electronics' technical staff is also available to answer any

questions that might arise concerning the installation or use of your
Patton Model  2090.  Technical Service hours:  8AM to 5PM EST,
Monday through Friday.

Summary of Contents for 2090 Series













Reviews: