background image

Page 6 of 9

USER GUIDE  (CONTINUED)

8. Press  Fig.4“      ” icon, 
    select “Functions”, you can
    choose “Test”, “AUTO”, or
    “Custom Setting” which have
    been adjusted to edit your 
    settings. 

9. Press Fig.8 “Change image”.And 
    touch “take photo” to take a 
    photo . 

9.1 Click “      ” to grasp a 
       your desired view 

9.2 Click “      ” to take a photo. 

9.3. Adjust the photo to trim 
       the photo’s desired size.
       Then click “      ” .

7. Select “Custom Settings” in Manual 
    override. Adjust the “Duration”

 

as

    desired, the “4hr” is the default.The
    light will turn to your setted high 
    level brightness for your setted 
    duaration,then turns to “AUTO” 
    mode. The setting will be avaliable 
    only at this night. Next night the 
    light will turn to “Clock time(End 
    Time”mode. Adjust the “Clock 
    Time”, the “9PM” is the default. The 
     light will turn to high level 
     brightness you set for the 
     pre-setted “Clock Time”, then turns 
     to “AUTO” mode at your 
     pre-setted time.

Note

: If your settings on the 

     “Manual override”mode forget 
     to save, the settings will be 
     performed for 2 minutes,then 
     the light will revert to phsical 
     switch’s control on the lamp.

Fig.7

Fig.9

Fig.9-1

Fig. 8

Summary of Contents for E6956W










Reviews: