background image

9

X

s

 Preamp Owner’s Manual

as previously indicated these buttons allow for the relative offset 

(displayed in 0.5dB steps) of  the slave (auxiliary) outputs in relation 

to the master (main) outputs.

The buttons on the hand remote duplicate most but not all of the 

functions on the X

s

 Preamp front panel.  Level setting for the slave 

(auxiliary) output is not available from the hand remote.  

From the hand remote you can direct access the following functions:

Phase: flips the absolute phase of the output. A “-” will appear on 

the preamp display to indicate the phase.

Mute: Mutes the output.

inputs 1-5: duplicating the manual Input < and Input > buttons on 

the front panel.

Tape button, selects and deselects the tape input (virtual input #7).  

Tape output is always live.

Balance < and Balance > buttons set the relative levels between right 

and left channel.

Volume ^ increases the output level in 0.5 dB steps to a maximum of  

+9.5dB

Volume v decreases the output level in 0.5 dB steps to a minimum of  

–89.5 dB.

Pass Thru is a multi step software operation that selects the “pass-

thru” input (virtual input #6) and slowly ramps the gain up to 0 dB.  

At any time during the “ramp-up” period, a second button push 

will cancel the “Pass-Thru” command and operation.  Pass thru is 

intended to be used with a multi-channel processor.  This feature 

allows the multi-channel processor total control over the analog 

signal chain.

Ext amp on (External Amp On) This button toggles a voltage 

b12 Volts DC and 0 Volts DC.  This switched DC signal is 

available at both right and left channels of  the Xs-pre control chassis 

and is intended to control the turn on circuits of  the associated 

power amplifiers.  The power amplifiers if  so enabled can be 

connected to the red and white binding posts on the rear panel of 

the Xs-Preamp control which are marked “ext amp on”.

Display:  The display button controls the luminosity of the vacuum 

volume

display

ext amp on

pass thru

balance

tape

3

mute

5

4

2

1

phase

PASS

X

s

 Preamp

Summary of Contents for Xs Preamp















Reviews: