Pass Laboratories XA60 Owner'S Manual Download

Page: 9 / 14

XA60 Owner’s Manual

All figures obtained after 1 hour warm-up, with regulated 120 VAC
power line. See manual notes about AC power line regulation.

Gain

26 dB

Freq. Response

-3 dB at 1.5 Hz, -3 dB at 100 kHz

Power Output

60 watts max @ 1% THD,

1 kHz, 8 ohms

Maximum Output Voltage

plus, minus approx. 40 volts

Maximum Output Current

plus, minus approx. 5 amps

Input Impedance

22 kohm balanced

11 kohm unbalanced

Damping factor

30 ref @ 8 ohms nominal

Slew rate

plus, minus 50 V/uS

Output Noise

300 uV unweighted 20-20 kHz

Balanced CMRR

approx. -60 dB @ 1 kHz

DC offset

< 100 mv

Power Consumption

approx. 300 watts

Temperature

25 degrees C. above ambient at idle

Dimensions

19 “ W x 7” H x 20” D

Shipping Weight

68 lbs.

For more information please contact:

Pass Laboratories Inc.

P.O. Box 219,
24449 Foresthill Rd.,
Foresthill, CA 95631

Tel: 530.367.3690
Fax: 530.369.2193

www.passlabs.com

XA60 Specifications

“Pass”, “

pass

”, “Pass Labs”, “Pass Laboratories”, Supersymmetery”,

“Aleph”, and “Zen” and are all registered trademarks of Pass
Laboratories, Inc., and all rights thereto are protected by law.

Summary of Contents for XA60















Search results

Summary of Contents for XA60

Reviews:

Related manuals for XA60

Brands by name

Popular brands

Pass Laboratories XA60, Owner'S Manual

Search results

Summary of Contents for XA60

Reviews:

Related manuals for XA60

Brands by name

Popular brands