background image

8

XA60.5 Owner’s Manual

XLR.  If  you re-install the jumper incorrectly or leave it lying about, 
the amplifier will not work properly, and you will be able to tell.

Choose either XLR or RCA inputs.  If  you run both at once from 
different components, the sound is not likely to be optimal, but it 
shouldn’t cause damage anywhere.

Now that the source component is connected, turn the volume all 
the way down.  Plug the power cord back into the wall, and turn on 
the rear power switch.

Push the front panel button to activate the amplifier.  The lights will 
come on.

You are ready to play music

With any luck, you can now enter that blissful state, and we won’t 
expect you back for a while.

It’s always possible that something may go wrong.  If  so, don’t get 
excited.  We know It’s really aggravating when a product doesn’t 
work, but it will get fixed, and often it’s something really simple.  

We go to a lot of  trouble to make products reliable, and the failure 
rate of  our amplifiers is very low.  This is small comfort to the few, 
but take it easy and give us a call if  you have problems.

People are interested in how long it takes for these amplifiers to 
break in. Depending on the resolution of  the rest of  your audio 
chain, you may or may not notice any break in of  the amplifier 
beyond the first few hours of  operation. You will very likely notice 
the difference in sonic character between cold and normal operating 
temperature over the first hour, so we recommend letting these 
amplifiers warm up before any serious listening. 

This generation of  amplifiers warms up faster and is more bias-stable 
during warm up than previous versions, but we still recommend an 
hour for critical listening.  At the factory we adjust the bias and offset 
values initially and then after warm-up and then again after 48 hours,
If  necessary.  The “sweet spot” is a sink temperature between 50 and 
55 degrees C., but this is not critical, and will vary with your room 
temperature.  You should be able to put your hands on the heat sinks 
without undue discomfort for 5 seconds or so. 

The amplifier has a thermal cutout that will disconnect AC power if  
the temperature exceeds 75 degrees Centigrade.  This thermal cutout 

Summary of Contents for XA60.5














Reviews: