background image

4

XA60.5 Owner’s Manual

All the usual performance metrics - power, distortion, noise, input 
impedance, damping factor and bandwidth have all been improved 
in this latest generation.  The power supplies are larger, with fast 
rectifiers gating to larger capacitor banks.  The increases in AC line 
noise worldwide have been addressed with heavier EMI filtering 
and dramatically quieter power transformers.  In addition, through 
improved biasing regulation, the circuits give much more consistent 
performance under varying AC line voltages and over a variety of  
ambient temperatures.

All this is very nice, but only if  it improves your listening experience.  
We listen very carefully and critically to our amplifiers with a wide 
variety of  associated equipment and we take our time with it.  
Musical performance is most important, and is the basis of  our 
success over the years.

It’s true that we also value the other things.  The design and 
manufacturing decisions have to balance subjective performance 
against reliability, cost, specs, and ego (in approximately that order).  
That is why we make more than one amplifier, but all are built with 
the same commitment to quality.

If  you have purchased this amplifier, we thank you for your 
confidence, and hope that you enjoy it for many years.  If  you have 
any questions or comments, or if  we can help you with your audio 
system, pelase don’t hesitate to contact us.

[email protected]

www.passlabs.com

Tel  (530) 367 3690 

 

Fax  (530) 367 2193

Pass Labs,
PO Box 219
24449 Foresthill Rd,
Foresthill  CA  95631

Summary of Contents for XA60.5














Reviews: