background image

Set Up the Hardware

 PS

-

3208

3

013-15272B

LED Information

The Bluetooth and the Battery Status LEDs operate as 

follows depending on the type of connection:

For a wireless Bluetooth connection:

For a micro USB cable connection to a USB 

port

:

For a micro USB cable connection to a USB 

charger

*Logging: PASCO wireless sensors can either stream 

live data to a compatible device for “real-time” viewing or 

log data (save it to the sensor’s memory). After logging, 

the data can be uploaded to the computing device for 

display and analysis at a later time. Logging capability 

supports long-term or remote data collection while not 

connected to a device. 

Set Up the Hardware

Warm-Up Time

Turn on the sensor and connect it to a computing device. 

Let it come to equilibrium with the environment where it 

will be used. Allow 180 seconds (3 minutes) for the sen

-

sor to equilibrate. Variations in temperature, humidity, 

and air pressure can impact the calibration so equilib

-

rium with the environment is critical

Calibration

The sensor has a one-point calibration in the software 

with a default value of 400 ppm (user editable). If you 

have a meter that provides an accurate carbon dioxide 

measurement, you may want to edit the default value. A 

two-point calibration is not possible. The user can reset 

to the factory calibration which is stored in the probe at 

any time.

Sensor Operating Theory

Concentration of carbon dioxide is measured by non-dis

-

persive infrared (NDER) technology. The sensing ele

-

ment is a pyroelectric device that senses the carbon 

dioxide gas concentration by measuring the amount of 

infrared (IR) energy absorbed by CO

 gas in the probe 

housing. The infrared (IR) source at one end of the 

probe is a lamp with a quartz envelope and a gold plated 

reflector. The sensitive thermopile element at the other 

end of the probe is covered with a narrow band filter that 

only passes IR energy at 4.27 microns; a wavelength 

that is absorbed by the CO

2

 gas in the probe housing. 

As concentration increases, the IR energy ‘seen’ by the 

thermopile decreases.The relationship between the gas 

concentration and the absorption of IR energy is similar 

to that of Beer’s Law.

Storage and Maintenance

Do not use or store the sensor in a highly dusty 

environment. Avoid direct sunlight or heat radiation.

Do not let the sensor get wet.

Bluetooth 

LED

Status

Battery 

LED

Status

Red blink

Ready to pair

Red blink

Low power

Green blink

Connected

Yellow blink

Logging*

Bluetooth LED Status

Battery 

LED

Status

OFF

--

Yellow ON

Charging

OFF

--

Green ON

Charged

Yellow blink

Logging*

Bluetooth 

LED

Status

Battery 

LED

Status

Red blink

Ready to pair

Yellow ON

Charging

Green blink

Connected

Green ON

Charged

Yellow blink

Logging*

Rubber collar

Sample bottle 

and cap

CAUTION: Do not wash 

the sampling bottle in a 

dishwasher or autoclave. 

It will melt.

Summary of Contents for PS-3208








Reviews: